Jump to content
SAU Community

Recommended Posts

The other day I mounted a bosch 044 intank in my r33. At first I left the one way valve thingie on, finished the install and the car didnt start. So I pulled the pump out again and removed the valve as I had been told by another r33 owner he did it the same way with no problems.

Well the car ran perfectly for about 5 mins then it stalled. And now it wont run any longer then 10 seconds.

It sounds like the car is running out of fuel but it isnt. I took the hose of at the fuel filter to check it wasnt a clogged filter or something but there seems to be a nice flow happening.

Any thoughts?

Any one else think its not pump related?

Thanks

David

Link to comment
https://www.sau.com.au/forums/topic/106601-need-help-with-044-install/
Share on other sites

YEP, you need to bypass the fuel pump controler. (drivers side on the parcel shelf)

basicly run a seperate earth to the pump directly, also run a power wire directly to the pump.)

the relay is on the side of the boot fuse box.

if you can, remove the fuel damper of the fuel line in the tank (the metal thing inbetween the pump and the sender)if it has it....

its purpose is to "dampen" the fuel lines, to stop the hammering noises you get through the lines from the injectors pulsing,

this device can cause the pump(bosch roller cell) to cavitate when the fuel is hot.

the 1 way valve should be removed off the pump to

(unless you use banjo fittings on the pump with a cap bolt on the pump ie:blocks of the thread on the pump fitting with the banjo fitted..)

Ok thanks for the help. I already earthed the ground of the pump. what should i do with the earth lead that goes back to the power fc? Ground it or leave it bouncing up and down with the road??

R31Nismoid ive read that diy aswell as many others and no ones had this problem.

Thanks again ;):D:D

edit. I also drilled straight through the one way valve so I can get a hose to fit on it :D

Edited by 33SOM

I just hooked up a 40 amp relay directly to the pump. It sounds healthier now but the car still wont start.

I also took TO4GTRs advice and bypassed the fuel damper thingie and still no go.

Anyone got anymore ideas?

Im about to throw the standard pump back in to make sure it is the pumps fault the car wont start...

  • 1 year later...
  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is anyone running these axles? R32, R33, R34 GTR front Axles. shafts itself rated 950hp. Suit all RB26 engines Croydon, Melbourne, Victoria Would be nice to pay half the cost of Driveshaft Shop Axles. I'm building an AWD S13 Coupe that is very low ride height (high cv angle) compared to stock R32. Has an RB30 with appx 600whp. Just looking for feedback. Thanks, Josh- https://www.instagram.com/feng_shui_garage/
    • Been a long time since r31 got some love, my brother dropped a shitbox ls1 crapadore in my lap to fix up.  Put a wiper motor in as the flooded one was no longer alive.  got windscreen wipers now. Time to clean respray and install back in the titanic  IMG_0505.mov
    • Nah its a server spammer thing  Although, now that I manually approve all the accounts I can probably loosen up some of the restrictions.  
    • Thread bump, again! Although, no bad news this time. Posting for the sake of possible root cause. Basically, I rebuilt it (mostly stock), installed Haltech + sensors, had it running fine on new ECU.  Still not really understanding why it cracked pistons last time. Got to tuners, and while checking timing, noticed +-10deg of timing scatter while revving. Changed CAS, and it was rock solid. While not definitive, can't imagine seeing 20+ psi with that amount of scatter would be a good thing. Also glad I found something.   Bit more of a run down; Carried out a stock rebuild, a set of stock pistons, out of a spare bottom end. Everything stock apart from head studs and oil restrictors. (so I can pretend I didn't let the Nissan out, ha.) Armed with the measuring gear and FSM, set about doing overhaul. Oil restrictors as per oil control thread for a RB25, stock oil pump, drifting. Head drain/vent from rear of head, to passenger side of sump above oil level. Two dash 10 vent lines from drivers side of sump (unused atm) Hi octane style cam cover breather kit Splash covers over last 2 cam caps. Both breather lines from cam covers to vented to atmosphere catch can, not plumbed back into sump (wanted to see what it was actually breathing). Got it run in (did about a 1000km) no to low boost scenario, As I had questions over old ECU setup. Installed haltech +sensors for flex Retune on E85 (finding CAS Issue along the way), made 300rwkw at 20psi, out of wastegate. Did a drift day the next day (yes, it was a big weekend!) and was checking catch can throughout the day, ZERO blowby. I mean nothing. Lines from cam covers are not even wet. Done a bunch of street driving, spirited and catch can is still dry. Early days I guess, but pretty happy so far. Also now run 10w60, up from the 10w40 that I used to run. Oil pressure is significantly better, especially when hot (as you would expect)      
×
×
  • Create New...