Jump to content
SAU Community

Recommended Posts

  • Replies 181
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

can we set a cut off date for payment? It just seems to be taking a long time for people to pay after expressing interest and i'm quite keen to get things happening. :D

can we set a cut off date for payment? It just seems to be taking a long time for people to pay after expressing interest and i'm quite keen to get things happening. :D

sent u a pm mate :) To everyone else wondering about closing dates what happens is i need 5 people minimum to get the low price from Noltec. Once over 5 i can still get the same low price.

What has happened is i have enough people to place 2 separate orders through. Im taking the 5 guys who got in first and ordering their stuff now, and the last 5 guys who payed me (or im waiting for) will have to wait for that separate lot to be payed in full to get their group order of 5 placed. It shouldnt take too long for their order to be paid anyway.

Thanks everyone so far.

sent u pm too :)

Look guys as i said above ive got enough orders now to cut off the first group and place an order through.

If you have ordered a while ago u are on the first list. (if unsure pm me and i can tell u on which list u are on)

I did say about this happeneing in my first post though of the gb. Sorry i shouldve said what was going on with the orders again to make it clearer.

Beer Baron / Roy: Sorry I've been so slow to get around to this. As I explained to Bl4cK32, I've been the only one looking after work for the past fortnight (everyone pissed of on an overseas training junket) and just haven't had time to organdise (winnie the pooh stylee) payment, etc for this. Hope it doesn't cause any major inconvenience.

haha i wasnt talking to you mate. you have paid ;) I was just trying to stimulate some more people that had said 'in' into paying up so we can get the show on the road. :D

PM sent again Darren, just let me know when to send bud. :D

P.S - have you started or are you going to start a group buy for other Noltec products? Mainly the camber/caster radius rod bushes you were talking about before? I'd be pretty interested. :)

Quick update guys - R32 subframe - I rang Noltec to confirm stock levels. They only have 3 on the shelf. Not to worry he said, as they are running more as we speak, and they should be in soon. As soon as they are in, the order will be placed.

This happened with the r33 bushes as well, no big dramas though, as they came thorugh earlier than Noltec said. So we should see some soon :(

Sorry for this delay guys....

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...