Jump to content
SAU Community

Recommended Posts

Under what conditions do the customs guys deem your car to require a steam clean after it's come off the boat. I got pics of my R33 just before it left Japan and at that time it had a full detail inside & out and was immaculate (including the engine bay). It arrived in the port about 2 weeks ago and now I've been waiting about a week for my car to get steam cleaned, also referred to as a "Quarantine Wash". A healthy $60 charge to transport the car to a wash station (1-2km away from the wharf) and another $97 to wash the car is included in my bill.

Sure - if a car is quite dirty it might need a clean but mine was seriously immaculate. Is it a scam to make money for the cleaning guys? Or would each car genuinely require a wash like this.

It's an AQIS thing (Australian Quarantine and Inspection Service). Basically they're looking for bugs and things like dirt/mud in the wheel arches/under the car. Foot and mouth disease is one of the big concerns. So if the AQIS inspection detects something they don't like or are not sure about they'll demand a steam clean. Not much you can do about it (well, nothing really). My car didn't need it.

at sydney docks i dont know of any car that didnt get steam cleaning requested. and in sydney it's 220 or 230 depending on which place you go to.

i've had a car require a pressure wash at brisbane docks, it was only 60 there. not much you can do, if they request it, it has to be done. simple.

Even if its spotless they look around the fuel filler, inside the little door and if there is any dirt there ( always is it sticks to the old fuel ) they want it steamwashed . Mine was spotless i detailed it myself in japan and they picked the fuel filler, thats all they had to clean and Hobbs charged me $120 if i remember right .

Yep *cha-ching* they *cha-ching* sure *cha-ching* are *cha-ching* busy *cha-ching* cleaning *cha-ching* cars *chahahahaha-chiing*

What is it, a few thousand cars per ship x $220-230 each = plenty of *cha-chinging* -erm, cars to wash.

Unfortunately not much we can do about it.

dont bank on it, they do fcuk all cleaning as they are very busy counting money.

I have to agree with that, the only other thing i have to ad, they try to steal stuff from them .

They take their sweet f**kin time too. I've had my car in the queue to get cleaned, with the other imports for 8 days now and it hasn't been done yet. I've been advised that it may take another 2-3 days. Just like trying getting your car ON the boat at Japan, it seems that new cars take precedence over 2nd hand imports when they reach Oz as well.

Edited by MearCat
dont bank on it, they do fcuk all cleaning as they are very busy counting money.

My car was held up at quarantine, i thought "$200 atleast my car will be steam cleaned", spoke to the dead shit who was meant to do it and all he did was high pressure spray the car. Probably made it more dirty then clean if anything. Beurocratic bullshit.

My 'steam cleaning' took the best part of about 1 minute (literally). It involved the guy rinsing under the car and in the wheel arches with a hose.

When I gave him my key, he just chucked it on top of a drum sitting out in the yard. I picked it up straight away and near slapped his bitch ass back to where he came from....

bloody rip off schemes. I've heard many stories of parts or even whole cars stolen from hobbs

Next time, i just won't get it steam cleaned, and wait and see if quarantine/customs calls me. I'll just say it was cleaned and see what they say.

I dunno how Hobbs is now since they've moved, but it wasn't secure before.

Anyway in Sydney they can now clean your car at the docks so you don't need to arrange to take it to Hobbs or anything.

Had my car imported required a steam clean and I thought fair enough.. Put it up on the hoist, was checking around the car. Gave the rear bumper a bit of a bash and a bit of sand and grass feel out. So much for thorough cleaning and decent quarantining. Oh yeah and they swung $330 odd dollars for cleaning the entire car.

I picked up my car today and I asked the guy at the cleaning place why he thought my car had to have a wash. He said "This car is one of the cleanest cars I've seen in a long time. I have absolutely no idea why they would want it done. It certainly didn't need it"

When I got the car home, I proceeded to pull out all the stock parts that were sitting in the boot... in plastic bags... full of sand.

I CALL SHENANIGANS!!!

  • 3 weeks later...

I'm due to go and pick up my linesky at Glebe Is. (sydney) soon.

And since I know someone who can steam clean my car, I might just ask them if he can do it instead.

You think they'll allow it?

I cant really afford the extra $200 cos i imported the car on a shoe string budget.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...