Jump to content
SAU Community

Rb25det Turbo Upgrade

tx240

By tx240,
in Classifieds

 Share

Recommended Posts

tx240 Apprentice

tx240

Posted
Posted

item:

bolt on upgrade turbo for RB25det, 350HP

description:

this turbo uses the factory nissan covers with a brand new 350hp Garrett ball bearing core, everything bolts up to factory mounting positions, only mod needed is to oil and water lines. covers have been cleaned and bead blasted.

price:

$1950

location:

darra, brisbane

contact:

(07) 3375 3755, 0404841629, ask for ross or josh

Link to comment
https://www.sau.com.au/forums/topic/108709-rb25det-turbo-upgrade/
Share on other sites
tx240 Apprentice

tx240

Posted
  • Author
Posted
Seems a bit rich to me? 350HP @ $1950.

this turbo was built by turbo Australia and is the smallest of the upgrades that they perform. they do the same thing for the other stages but use a larger core for more HP, they go as high as 550HP for $2090. the one im selling is for a pretty much stock engine and is desighned to be a direct fit replacement for the stock ceramic turbo. due to garretts ball bearing desighn, and the use of a steel wheel, gives these turbo's the ability to get onto boost as quickly as the factory setup but the steel wheel lets you screw more boost out of them. so in fact it is a much better unit than the factory item.

also, the reason they call it the 350hp upgrade is beacause it uses a 350HP garrett core, just in case you didnt know.

tx240 Apprentice

tx240

Posted
  • Author
Posted (edited)
Dyno graphs???

Also your "unoffical site" says $1,750 plus GST which equates to $1,925....

Has this been highflowed or just the core replaced???

Also 360 degree thrust bearing????

there are no dyno Graphs as yet but we are hoping to get some more feedback from a few customers that have recently fitted them.

i know what the website has as far as pricing goes but i miss typed it for this post so it is for sale for $1925 including GST.

this turbo has been highflowed, and garrett ball bearing cores do not have thrust bearings of any kind as the journal bearing are angular contact ball bearings.

Edited by tx240
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Tomei gasket

      By joshuaho96 · Posted

      I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...