Jump to content
SAU Community

Wtf My 4 Seater Is Complied As A 5 Seater

Hootchy
 Share

Recommended Posts

Hootchy Community Regular

Hootchy

Posted
Posted

I took my series 2 r33 gts-t coupe in for a blue slip today as I'm changing the rego from ACT to NSW.

The mechanic points out to me the compliance plate which clearly states a seating capacity of 5.

any body can see that they're a 4 seat car

He'd already rang (insert proper authority here) and they gave him no real answer.

unsure of what to do he told me to fit a centre seat belt in the back for it to pass.

Am I going to be the only 5 seat r33 in NSW ? or has someone else been through the same thing?

MANWHORE Grand Master

MANWHORE

Posted
Posted
My R32 GTS is complied as a 5 seater but only has 4 seats.. whats the deal there? are all two door R32s four seaters? i bought it a couple of weeks ago and the rego had run out, i just got new rego no probs

End of Story: r32s-34s came from nissan as 5 seaters. I.e. they all had a lap seat belt. There is no such thing as whether the compliance place bothered to 'install' a centre belt, because they already had one.

There is no reason for them removing it either. Strange things happen, maybe it was cheaper for them to obtain their compliancing for that model of car by removing the centre seatbelt.

Just check that the centre belt hasn't fallen into the hole. If it has, i'm sure you'll be able to find one off a wreck for like $20-50$. There will already be reinforced holes for the buckle and belt under the seat.

Hootchy Community Regular

Hootchy

Posted
  • Author
Posted
End of Story: r32s-34s came from nissan as 5 seaters. I.e. they all had a lap seat belt. There is no such thing as whether the compliance place bothered to 'install' a centre belt, because they already had one.

There is no reason for them removing it either. Strange things happen, maybe it was cheaper for them to obtain their compliancing for that model of car by removing the centre seatbelt.

Just check that the centre belt hasn't fallen into the hole. If it has, i'm sure you'll be able to find one off a wreck for like $20-50$. There will already be reinforced holes for the buckle and belt under the seat.

All seat belts get replaced to australian approved ones and I'd say when it went through compliance the

work shop was to lazy/cheap to put the centre belt in

666DAN Grand Master

666DAN

Posted
Posted
End of Story: r32s-34s came from nissan as 5 seaters. I.e. they all had a lap seat belt. There is no such thing as whether the compliance place bothered to 'install' a centre belt, because they already had one.

There is no reason for them removing it either. Strange things happen, maybe it was cheaper for them to obtain their compliancing for that model of car by removing the centre seatbelt.

Just check that the centre belt hasn't fallen into the hole. If it has, i'm sure you'll be able to find one off a wreck for like $20-50$. There will already be reinforced holes for the buckle and belt under the seat.

As Hootchy said, they have to be removed when complied...so yeah I'll stick to my previous comment of lazy compliance companies that don't do their job and replace them...I know for a fact my current R34 was complied to the letter, my last one was questionable.

lang Collaborator

lang

Posted
Posted

well, not only is my R32 GTR registered as a 5 seater (and please dont tell me my car came from nissan as a 5 seater) but on my rego sticker my car is registered as a "nissan sedan". My car could be a maxima for all transport SA knows.

Note: i did all the regency paperwork and took the car through myself after compliance and did not mis-represent the car in any way

MANWHORE Grand Master

MANWHORE

Posted
Posted
well, not only is my R32 GTR registered as a 5 seater (and please dont tell me my car came from nissan as a 5 seater) but on my rego sticker my car is registered as a "nissan sedan". My car could be a maxima for all transport SA knows.

Note: i did all the regency paperwork and took the car through myself after compliance and did not mis-represent the car in any way

yes lang, believe it or not, ugly poo gtrs are 5 seaters from nissan. Although it doesn't look like you can sit on the hump, it is a seat.

How do I know? when we brought in a couple of them (reads - my dad has 1, bro has one) they both had middle lap belts from japan.

Your copmlier obviously removed them.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...