Jump to content
SAU Community

Recommended Posts

Positives:

- Looks awesome to people who appreciate it..

Negatives:

- Incorrectly used, you can smash your front bar onto the pavement!! Not to mention exhausts etc.

- Shitty car handling. I've heard that it makes your car handle like a boat, even when lowered!

- EXPENSIVE!!

- 70% of people (IMO) will think you're a total tool.. :D

Edited by Primordial
Positives:

- Looks awesome to people who appreciate it..

Negatives:

- Incorrectly used, you can smash your front bar onto the pavement!! Not to mention exhausts etc.

- Shitty car handling. I've heard that it makes your car handle like a boat, even when lowered!

- EXPENSIVE!!

- 70% of people (IMO) will think you're a total tool.. :P

Amen.

Hydraulics are definetly not allowed in nsw, Airbags (bags as truckers call them) are ok. I have plenty of mates into the whole truck thing. Also have a mate with a bagged cresida now it is cool it is somethin very different.

Each to there own, where as the handling comment when the bags are right down it handles like a boat but when the bags are full of air it is seriesly stiff.

my 2c worth

Jamie

yeah, def not in a line eh! bag- snags, it's all wank, im mates wit the guy wit the cressie 2, IT'S PHAT, like ol' grandpa joe stlye and shit... but i have a mate wit a bagged lux, pretty cool, but as i and mate say, it's pretty W.A.N.K. also had a mini- dick show here in port cuppl weeks back, some were pretty sweet, but the majority were just all covered in primer... like jamie said, 2 each there own... Keep it spooln..........

Agree fully brett W.A.N.K factor. But you no the funny thing is most our cars are as low as there's an we aint on bags and we dont have as much bog, im guessing the idea of bog on the trucks is the extra weight will lower it some more im guessin thats there idea anyways. Dont think i dont appreciate a good truck because i do but i just find it hard to understand why most of the trucks are WORK in progress.

They (well most of them) live on a diet of wank and bongs...

should've seen all of them stoned runnin round at the truck show here a cuppla weeks bac... stupid f**ktards... yeah, its not a mini truck wothout bog or the occasion thong to go with it... ha ha... Like i said previously keep spooln!

dont get me wrond, sum trucks are sik! but why waste a turd load of money on somethin that lasts 5 mins but takin 10 mins to wait for the 5 mins again, (air runs out- compressor refilling-3 hours 34 mins later, yay more air)-spose its better than drugs but they still do that!

Hydraulics are definetly not allowed in nsw

that's news to me. I drive a car with hydraulic suspension pretty much every day. my soarer is one of 800 to come equipped with full hydraulics. (no not the usual shithouse soarer airbags). It was complied and registered in this state.

Love airbags n hydro's... both our VIP Celsiors have airbags (factory with aftermarket controllers to allow em to sit an inch off the ground) and the Maxima has hydros...

post-12522-1128253996.jpg

post-12522-1128254044.jpg

post-12522-1128254100.jpg

CIMG0032.JPG

CIMG0035.JPG

doin the dogleg (one wheel off the ground)

CIMG0044.JPG

Hydraulics suck for handling and ride comfort,because its like having no springs at all and dampening is only provided at the midpoint of the height, ie there's no travel in shock absorption at full height and minimum height. They pull the chicks though... apparently. Airbags are much nicer for handling and ride comfort. Get an Air Strut though... they're replacement struts with airbags built in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...