Jump to content
SAU Community

Recommended Posts

Circuit, drag or drift RB’s with excess oil in the cylinder head, not enough oil in the sump, oil in the catch can, wet sump, oil surge, lack of oil, big end bearing failure etc

I get about 10 X PM’s a week from guys with this problem, I have posted up what is required many, many times. But still the guys want a solution after they have assembled the engine, it is in the car and they now have a problem. Well the bad news is there isn’t one solution. The answer is to do all of the steps when you are assembling the engine and then you won’t have a problem. There is no one magic, off the shelf solution. Buying a brand name restrictor, sticking it in the block and expecting that to fix the problem on its own is naive at best. Similarly fitting a baffle in the cam covers may overcome the catch can problem but it will still leave the others. :P

On the circuit race cars we take a 5 step approach in controlling the amount of oil that is trapped in the cylinder head and/or blown into the catch can; :D

1.Block off one oil feed in the block (RB26’s have this standard)

2.Fit an appropriately sized restrictor to the other feed. The size of the oil pump is one of the determinates for the size of the restrictor, ie; a high flow, high pressure pump needs a smaller restrictor. Constant higher RPM needs a smaller restrictor etc.

3. Fit an external oil return from the rear of the cylinder head to the sump

4. Drill out the oil return galleries in the head and block

5. Machine around the oil return galleries to facilitate access for the oil

It seems to me that many guys do #2, and some maybe #1. If you haven’t done #3, #4 or #5, then please remember that they are cylinder head off jobs. Drill out the oil return galleries in the head and block is pretty much self explanatory. As is machining (die grinder) around the oil return galleries to facilitate access for the oil to the return bgalleries. The external oil return fits to the rear of the cylinder head at the Y, there is a welsh plug there that you can remove and replace with a fitting. Then braided line to another fitting in the top of the LHS sump wing if you have one. If you don't, then you should for circuit and drift work.

I have tried to include every commonly used word that I can so that this post pops up when a search is done on this problem. Maybe that will cut down the PM's to only 5 a week :(

:D cheers :D

PS; this post is not designed to stop people asking questions via PM's, maybe just reduce the repetitive ones. Plus it will hopefully save people a lot of money pulling the cylinder head off to do what is easily done for very $few when the engine is being built in the first place.

Edited by Sydneykid
  • Like 2
Sk in your experience do RB20's and 25's suffer this problem as much as RB26's? or is it more related to the greater grip and g's that a GTR creates causing the problem? or is there a design issue across the whole RB range?

Yep, it's all RB's, the block, oil feed and return systems were designed for ~6,000 rpm occasionally. Circuit, drift and drag means higher than that rpm and for longer periods of time.

:P cheers :)

  • Like 1
For the oil return on an rb26, can you add a fitting to the standard sump or does it need to be a custom sump? Thanx

If you are maintaining sustained high rpm for long periods (such that it affects the oil return) then I would respectfully suggest that a sump upgrade is necessary.

So to answer the question, yes you can. Since the crank turns clockwise (looking from the front) plumbing the oil return into the top LHS of the sump would be logical. That way it is feeding into the partial vacuum created by the crank spinning.

:dry: cheers :)

Edited by Sydneykid
  • Like 1
Craved - you can't miss it if you are looking at the back of your head... so to speak. :)

hahahah ok :dry:

i had a look at the head before i left for work .. there are 2 welsh plugs there.. both rather large..

any details on the process of getting a fitting in there? sizes?

look like about an inch i diameter for the top one, and slightly larger for the bottom one..

do you tap into,braze on a fitting to the welsh plug or run something the full size?

Thanks SK.

I've had my blocks head oil return honed to improve oil flow however the actual head hasn't been played with.

My heads being pulled off next uni holidays, I will then drop in one 2mm restrictor and block the other.

I'm still a little concerned blocking off one restrictor with a hydraulic head being predominately street driven.

Thanks SK.

I've had my blocks head oil return honed to improve oil flow however the actual head hasn't been played with.

I'm still a little concerned blocking off one restrictor with a hydraulic head being predominately street driven.

yeah same, thats why i was thinking the 1.5mm x 2 with the extra return line in the back of the head...

i'll be getting the head and block returns "matched" the help as wells as a hone on the block feeds.

Do remember Craved that you have an extra oil feed from the VCT were as I don't.

I would feel perfectly safe running an R33 VCT head with only one block oil restrictor. As essentially the head is then receiving oil from 1 x 2 mm and 1 x 1.2mm oil feeds.

The R32 RB25DE head on the other hand doesn't have a vct oil feed.

I ran running 1 feed by my head bloke (Chris Milton Engineering) he was concerned with the hydraulic head receiving oil from 1 feed.

He said on a prior rb30det they did ran a vct r33 head they left the rb30's standard 1.8mm restrictor in place, blocked off one and obviously ran the vct feed supply. It was fine.

I didn't have my motor built by Milton Engineering as they wanted too much.. I almost fell out of my chair... Only the head was rebuilt as they had previously had experience with them.

In a round about way I am asking Gary if he has ran an R32 RB25DE head with only one oil feed for a duration of time without experiencing issues.

Gary has mentioned the R33 head but not the R32 head.

was my understanding that the VCT feed didn't lubricate the head, only pressurised the inlet cam VCT unit, then drained directly back down and not out in the head to feed the lifters and lubricate the cams etc... i could be wrong of course.

I don't know if the vct feeds the lifters with oil pressure, the only real way to tell would be to some how trace the oil galleys in the head.

I'll be doing this with my r32 head, I'd assume both oil feeds are joined and not seperate.. For example not joined oil galleys: rear oil feed supplys the rear cam bearings and lifters, front oil feed supplys the front cam bearings and lifters.

Do remember Craved that you have an extra oil feed from the VCT were as I don't.

I would feel perfectly safe running an R33 VCT head with only one block oil restrictor. As essentially the head is then receiving oil from 1 x 2 mm and 1 x 1.2mm oil feeds.

The R32 RB25DE head on the other hand doesn't have a vct oil feed.

I ran running 1 feed by my head bloke (Chris Milton Engineering) he was concerned with the hydraulic head receiving oil from 1 feed.

He said on a prior rb30det they did ran a vct r33 head they left the rb30's standard 1.8mm restrictor in place, blocked off one and obviously ran the vct feed supply. It was fine.

I didn't have my motor built by Milton Engineering as they wanted too much.. I almost fell out of my chair... Only the head was rebuilt as they had previously had experience with them.

In a round about way I am asking Gary if he has ran an R32 RB25DE head with only one oil feed for a duration of time without experiencing issues.

Gary has mentioned the R33 head but not the R32 head.

The R32 RB25DE cylinder head requires oil flow the same as an RB20DET cylinder head. The questions are still the oil pump flow and pressure, the rpm commonly used and the length of continuous time that rpm is used. Plus what work has been done on the oil return system. So it’s not a simple one size answer, it’s more a 3 dimensional table. If I have time I will make up a rule of thumb table and post it in this thread.

:laugh: cheers :P

The R32 RB25DE cylinder head requires oil flow the same as an RB20DET cylinder head. The questions are still the oil pump flow and pressure, the rpm commonly used and the length of continuous time that rpm is used. Plus what work has been done on the oil return system. So it’s not a simple one size answer, it’s more a 3 dimensional table. If I have time I will make up a rule of thumb table and post it in this thread.

:) cheers :D

]

A table would be GREAT, go Gary.

  • 2 weeks later...

regarding restrictors and such, what kind of restrictors should one use on a rb20 using a n1 oil pump?

also ive a shot the back of my head and not sure where i should fit the external drain, advice on both q's is always appreciated.

post-9364-1144374319.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...