Jump to content
SAU Community

Recommended Posts

NP mate. it does not require welding but it will require your machineist to machine down the crank and fit it correctly. its not a easy job and you have to have the crank out of the engine to do the task.

what was the other question? did you read through this thread ? it has everything you need.

always balance everything that goes up and down and round and round. Might as clean up the crank too while there, any dags and casting marks clean it up and get it slippery smooth.

In regards to the RB25 , why is the front feed blocked off and the rear feed restricted but with the other engines its the rear feed that gets blocked off and the front feed get's the restrictor as per sydneykids table ??

we dont know where sydney kid comes up with his ideas but they have been proven to work time after time after time so its a good idea not to ask questions how he comes up with it...

I think it may be because the rb25 has hydro lifters and its required to have it setup that way to run them properly where the gtr has solids which does not need the same kind of oil configuration.

Mine is done as per Sydney kids instructions and its been running for 2 years and 363rwkw.

There are many others whos are running well too. I dont know why people have to question it all the time.

well i certainly do not know thats why i am asking these question's b4 i put the motor together .. i want to be 100% sure all is correct ..
in saying that guilt-toy if you install the non vct 25 head you block of the rear and feed the front but with the 25 vct head its opposite and both have hydraulic lifters..

thats is correct??

I run the non-vct RB25 head.

I blocked off the rear restrictor as the Rb26's are and run a 1.5mm restrictor up font.

Works fine no ticks, pops etc. Went from shit loads of oil everywhere over 5500rpm+ to a bone dry catch can. Still plenty of oil floating around in the cam covers. Prior on idle oil was puddled up to the base of the cam so you couldn't see the lifter. Now u can.

As a few have experienced; if you experience hydraulic lifter tick once the motor is warm its a tell tale sign the motors on its last legs. Recently happened to a mate of mine running an rb30det.

what went on your mates engine when it went ? i get lifter tick for about 5 seconds when i start the engine on cold startup only...

just wondering what went on your mates engine

I run the non-vct RB25 head.

I blocked off the rear restrictor as the Rb26's are and run a 1.5mm restrictor up font.

Works fine no ticks, pops etc. Went from shit loads of oil everywhere over 5500rpm+ to a bone dry catch can. Still plenty of oil floating around in the cam covers. Prior on idle oil was puddled up to the base of the cam so you couldn't see the lifter. Now u can.

As a few have experienced; if you experience hydraulic lifter tick once the motor is warm its a tell tale sign the motors on its last legs. Recently happened to a mate of mine running an rb30det.

what went on your mates engine when it went ? i get lifter tick for about 5 seconds when i start the engine on cold startup only...

just wondering what went on your mates engine

Lifter tick when the oil was warm and poor oil pressure no bottom end knocks or noises. The lifters were silent when cold.

Mine is fairly decent on cold start up, I only get an occasional tick. I can't remember the last time it ticked but I haven't been driving the car during the week for a while.

The RB20 was the same. Occasional tick.

Yeah well i checked my oil change sticker and it has been 6000km's since a oil change!! so thats why they would be ticking.. oil is getting a little old but its 300v chrono which is known to last longer then normal fully synthetic oil.

will change it in the next week or 2 :) ooooopppss

Lifter tick when the oil was warm and poor oil pressure no bottom end knocks or noises. The lifters were silent when cold.

Mine is fairly decent on cold start up, I only get an occasional tick. I can't remember the last time it ticked but I haven't been driving the car during the week for a while.

The RB20 was the same. Occasional tick.

thats a pretty over the top solution Beyond Horizon, you will never fit the standard piping back on if you go a fitting like that. A simple 90o angle with 1/2 hose barbs on one side and 3/8 BSP thread on the other can be tapped into the head just to the right of the fitting in that pic - much easier, smaller and about $3 for the fitting

thats a pretty over the top solution Beyond Horizon, you will never fit the standard piping back on if you go a fitting like that. A simple 90o angle with 1/2 hose barbs on one side and 3/8 BSP thread on the other can be tapped into the head just to the right of the fitting in that pic - much easier, smaller and about $3 for the fitting

But will it flow as well, bearing in mind we are talking gravity feed here?

thats a pretty over the top solution Beyond Horizon, you will never fit the standard piping back on if you go a fitting like that. A simple 90o angle with 1/2 hose barbs on one side and 3/8 BSP thread on the other can be tapped into the head just to the right of the fitting in that pic - much easier, smaller and about $3 for the fitting

Do you know where i can find some pictures of this modification you're talking about or do you have some ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
    • I believe @Duncan has given it a crack at Mt Buller before (in actual race conditions)
×
×
  • Create New...