Jump to content
SAU Community

Recommended Posts

Can anyone post up any pics of the mods to the oilways in the head & block. I'm just wondering which ones to drill out & which ones need opening/funneling out.

Cheers

Stu.

Very simple, all of the returns to the sump.

If it's not an oil return, then leave it alone.

Cheers

Gary

SydneyKid there is a hole in the block near to oil return... Is it a good idea to return the oils from the head there?

Depends on what block, generally speaking, no there isn't. That's why the suggested return is into the top LHS of the sump.

Cheers

Gary

  • 3 months later...

hey there,

just a question, ive read so much about the oil problems RB engines have, these cars arnt cheap to but, so much technology goes into development of these machines, and there seems to be about 6 problems with the oil side that sydneykid lists, why the hell have they not developed a better system of oil supply when testing their cars? or maybe nissan should have hired someone with a brain (sydneykid) to do the most critical part of a car engine????????

hey there,

just a question, ive read so much about the oil problems RB engines have, these cars arnt cheap to but, so much technology goes into development of these machines, and there seems to be about 6 problems with the oil side that sydneykid lists, why the hell have they not developed a better system of oil supply when testing their cars? or maybe nissan should have hired someone with a brain (sydneykid) to do the most critical part of a car engine????????

Ask Nissan???

If the GTR's were used and driven as a stock road car with no power mods etc, they would be fine 90% of the time.

They did fix the oil pump drive from late R32GTR's onwards(thats about it).

As soon as you push beyond factory specs and set limitations, that's where all these mods come in handy I'm sure.

I was lucky enough to see the inside of the engine that gibson motorsport built for kerry packer's car back in 91 last week. while they had made some mods, they didn't have:

external oil return

restrictor in feed to head (in fact they had opened both feeds!)

wide drive on the oil pump

expanded internal oil return at the rear of the block.

I think it is fair to say the development that gary and the race team have done on these motors over many years, and they fact they have been willing to share the knowledge at no cost is very valuable to everyone on these forums

oh, and it spun a bearing on its first track day....

I was lucky enough to see the inside of the engine that gibson motorsport built for kerry packer's car back in 91 last week. while they had made some mods, they didn't have:

external oil return

restrictor in feed to head (in fact they had opened both feeds!)

wide drive on the oil pump

expanded internal oil return at the rear of the block.

I think it is fair to say the development that gary and the race team have done on these motors over many years, and they fact they have been willing to share the knowledge at no cost is very valuable to everyone on these forums

oh, and it spun a bearing on its first track day....

Ouchhhh! That's expensive. How much was the engine back then....~150-200g?

Dunc, what changes have been made on the engine/car that caused the spun bearing? Was there any new oil pump, was the rpm limit raised, stickier tyres etc etc?

Cheap compared to a f--ked engine or engines especially if you plan on doing a lot of klm's on the track.

Dazmo, what kind of dollar is it for your dry sump and is there anyway of fitting one into a rb with Aircond and power steering intact :D?

You drill the smaller round holes to 9mm right?

I'm drilling mine out to 10mm, to match the head gasket.

Diameter of one of the oil drain holes, where it steps to the larger diameter is 9.65mm, and gasket was 10mm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...