Jump to content
SAU Community

Oil Control In Rb's For Circuit Drag Or Drift

Sydneykid

By Sydneykid,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 1.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

iruvyouskyrine
iruvyouskyrine

Whoops, yes i did mean catch can, corrected it now. Yes i understand that now. The two goals are to reduce the amount of oil entering the head, and equalize crankcase pressure. The oiling issue is s

fatz
fatz

less thinking more doing shit that works in the getto Dash ten on pasengers side Two dash 12 on the drivers side, angles and spaced so as not to hit shit and be able to tighten the f**ker up note

SimonR32
SimonR32

I ran my set up right up to 8800rpm at 2 bar (740rwhp) around the track with sticky R-comps the other night and not a drop out of the catch can. This is with no oil restrictors to the head and a stoc

Posted Images

mickr33couple Community Regular

mickr33couple

Posted
Posted

Narrow it down to ill be setting pressure to 70-65psi

Narrow the restritors to

Leave VCt, 1.3mm in the other two

Or

Leave VCt, 1.5mm and block rear, (or should this be block middle 1.5mm rear)

Abr33 are you running a head drain? Also are you running bigger sump with extended pickup?

abr33 Proficient

abr33

Posted
Posted

Doesnt really matter which oil feed gets blocked, it all runs a common gallery for lifters...

I have a gated and baffled sump that I made with better pickup, holds bit over 7 litres. If you need pics I think I put them up several pages back or can send more.

And have a rear head drain/vent also enlarged oil return channels and drilled return holes to 9mm. Also running front of sump to cam vent but will send it to a can soon.

brad 110 Collaborator

brad 110

Posted
Posted

Don't block the rear oil feed it does matter, block the centre at 75 to 85 psi max hot oil pressure if you leave the front restrictor std (which if you want the VCt to operate you should) and block the centre then reducing the rear to as little as 0.9mm combined with using a high volume pump so as oil pressure at idle is 30 psi or greater hot the lifters won't rattle.

mickr33couple Community Regular

mickr33couple

Posted
Posted

Don't block the rear oil feed it does matter, block the centre at 75 to 85 psi max hot oil pressure if you leave the front restrictor std (which if you want the VCt to operate you should) and block the centre then reducing the rear to as little as 0.9mm combined with using a high volume pump so as oil pressure at idle is 30 psi or greater hot the lifters won't rattle.

So many mixed story's, this thread has a graph on the first page and that says to block the rear?

brad 110 Collaborator

brad 110

Posted
Posted

Fine on a gtr head with solid lifters and no VCt. You have VCt and hydraulic lifters yes? Then don't block the rear, your engine builder would know this if they don't be concerned, mention loss over distance and gauge the response , trust me block the rear and the lifters at the rear of the head will define it for you.

mickr33couple Community Regular

mickr33couple

Posted
Posted

Fine on a gtr head with solid lifters and no VCt. You have VCt and hydraulic lifters yes? Then don't block the rear, your engine builder would know this if they don't be concerned, mention loss over distance and gauge the response , trust me block the rear and the lifters at the rear of the head will define it for you.

Yeah running hydraulic lifters and VCt, the engine builder didn't wanna put any in for the fact of noisey lifters...

Nitto website says dual spring crack off is 120psi... Single spring crack off is 75psi??

Should I do the single spring to give me the 75psi if this is max?

  • 2 weeks later...
VLSteve Enthusiast

VLSteve

Posted
Posted

Hello all.

I've searched but havent found the answer I'm looking for....

My motor is a Stock S2 RB25DET, standard bottom end and oil pump. But has Tomei Poncams and Hi flow OP6 turbo.

Its only street driven but with occasional drags.

What restrictors should I fit.

SK has said Leave VCT, block center and 1.5mm for rear.

From my searching I have found that the standard RB25DET restrictors are already 1.5mm. So all I need to do is block the center one?

Or is there no point in even removing the head to just to block off one restrictor with a stock motor?

Cheers

VLSteve Enthusiast

VLSteve

Posted
Posted

I am getting a bit of oil through my cooler piping etc as its running the stock breather hoses off the rocker covers.

Will look at a catch can.

Btw motor is out of the car at the moment, hence why I'm thinking of pulling the head to do the restrictors...

  • 1 month later...
skylinestx Apprentice

skylinestx

Posted
Posted

Hi everyone my name is stef..I hope someone can offer me some advice as I have read this hole thread from start to finish!

I'm in the middle of a forged rb25det build with an n1 oil pump.. After reading this thread I have come to the conclusion that I need to leave the vvt, block the middle and restrict the rear to 1.5mm. Now upon stripping the engine which I believe has been untouched I have found that all three restrictor a are 1.2mm which has now confused me lol..should I still block the middle supply and drill the rear out to 1.5mm? Thanks for any help

Regards

Stef

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Yeah I just got the head off mine this week. The front vct is 1.5mm and the other 2 are 1.2mm

Motor is a S2 RB25DET from a 95 R33.

So should I just put in 2x 1mm?

Depends on what pump you are using. I have an N1 pump RB30 block S2 head and I'm successfully using 2 x 1mm restrictors (street. track and to come - drags).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      My apologies. I forgot we were talking about weird beard M series stuff. Had been talking elsewhere with someone about an R33 with similar subject and got confused.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
×
×
  • Create New...