Jump to content
SAU Community

Oil Control In Rb's For Circuit Drag Or Drift

Sydneykid

By Sydneykid,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 1.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

iruvyouskyrine
iruvyouskyrine

Whoops, yes i did mean catch can, corrected it now. Yes i understand that now. The two goals are to reduce the amount of oil entering the head, and equalize crankcase pressure. The oiling issue is s

fatz
fatz

less thinking more doing shit that works in the getto Dash ten on pasengers side Two dash 12 on the drivers side, angles and spaced so as not to hit shit and be able to tighten the f**ker up note

SimonR32
SimonR32

I ran my set up right up to 8800rpm at 2 bar (740rwhp) around the track with sticky R-comps the other night and not a drop out of the catch can. This is with no oil restrictors to the head and a stoc

Posted Images

mickr33couple Community Regular

mickr33couple

Posted
Posted

Narrow it down to ill be setting pressure to 70-65psi

Narrow the restritors to

Leave VCt, 1.3mm in the other two

Or

Leave VCt, 1.5mm and block rear, (or should this be block middle 1.5mm rear)

Abr33 are you running a head drain? Also are you running bigger sump with extended pickup?

abr33 Proficient

abr33

Posted
Posted

Doesnt really matter which oil feed gets blocked, it all runs a common gallery for lifters...

I have a gated and baffled sump that I made with better pickup, holds bit over 7 litres. If you need pics I think I put them up several pages back or can send more.

And have a rear head drain/vent also enlarged oil return channels and drilled return holes to 9mm. Also running front of sump to cam vent but will send it to a can soon.

brad 110 Collaborator

brad 110

Posted
Posted

Don't block the rear oil feed it does matter, block the centre at 75 to 85 psi max hot oil pressure if you leave the front restrictor std (which if you want the VCt to operate you should) and block the centre then reducing the rear to as little as 0.9mm combined with using a high volume pump so as oil pressure at idle is 30 psi or greater hot the lifters won't rattle.

mickr33couple Community Regular

mickr33couple

Posted
Posted

Don't block the rear oil feed it does matter, block the centre at 75 to 85 psi max hot oil pressure if you leave the front restrictor std (which if you want the VCt to operate you should) and block the centre then reducing the rear to as little as 0.9mm combined with using a high volume pump so as oil pressure at idle is 30 psi or greater hot the lifters won't rattle.

So many mixed story's, this thread has a graph on the first page and that says to block the rear?

brad 110 Collaborator

brad 110

Posted
Posted

Fine on a gtr head with solid lifters and no VCt. You have VCt and hydraulic lifters yes? Then don't block the rear, your engine builder would know this if they don't be concerned, mention loss over distance and gauge the response , trust me block the rear and the lifters at the rear of the head will define it for you.

mickr33couple Community Regular

mickr33couple

Posted
Posted

Fine on a gtr head with solid lifters and no VCt. You have VCt and hydraulic lifters yes? Then don't block the rear, your engine builder would know this if they don't be concerned, mention loss over distance and gauge the response , trust me block the rear and the lifters at the rear of the head will define it for you.

Yeah running hydraulic lifters and VCt, the engine builder didn't wanna put any in for the fact of noisey lifters...

Nitto website says dual spring crack off is 120psi... Single spring crack off is 75psi??

Should I do the single spring to give me the 75psi if this is max?

  • 2 weeks later...
VLSteve Enthusiast

VLSteve

Posted
Posted

Hello all.

I've searched but havent found the answer I'm looking for....

My motor is a Stock S2 RB25DET, standard bottom end and oil pump. But has Tomei Poncams and Hi flow OP6 turbo.

Its only street driven but with occasional drags.

What restrictors should I fit.

SK has said Leave VCT, block center and 1.5mm for rear.

From my searching I have found that the standard RB25DET restrictors are already 1.5mm. So all I need to do is block the center one?

Or is there no point in even removing the head to just to block off one restrictor with a stock motor?

Cheers

VLSteve Enthusiast

VLSteve

Posted
Posted

I am getting a bit of oil through my cooler piping etc as its running the stock breather hoses off the rocker covers.

Will look at a catch can.

Btw motor is out of the car at the moment, hence why I'm thinking of pulling the head to do the restrictors...

  • 1 month later...
skylinestx Apprentice

skylinestx

Posted
Posted

Hi everyone my name is stef..I hope someone can offer me some advice as I have read this hole thread from start to finish!

I'm in the middle of a forged rb25det build with an n1 oil pump.. After reading this thread I have come to the conclusion that I need to leave the vvt, block the middle and restrict the rear to 1.5mm. Now upon stripping the engine which I believe has been untouched I have found that all three restrictor a are 1.2mm which has now confused me lol..should I still block the middle supply and drill the rear out to 1.5mm? Thanks for any help

Regards

Stef

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Yeah I just got the head off mine this week. The front vct is 1.5mm and the other 2 are 1.2mm

Motor is a S2 RB25DET from a 95 R33.

So should I just put in 2x 1mm?

Depends on what pump you are using. I have an N1 pump RB30 block S2 head and I'm successfully using 2 x 1mm restrictors (street. track and to come - drags).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Slight brake pedal stutter after new pads

      By MBS206 · Posted

      Johnny is sad now... Because you didn't get Bosch Motorsport ABS.  
    • PranK
      Slight brake pedal stutter after new pads

      By PranK · Posted

      Hey keep the ideas coming, I'm always keen on projects! But, problem fixed!  I got a cheapie ozito scope from Bunnings and had a good look in and around the bearing and sensor hole. I couldn't see a smoking gun but the bearing looked a bit strange, especially when comparing with a new one. I thought the cover had come off the bearing magnets.  Sorry for pics of a screen, I didn't have an SD card.     Good thing I had the old one to inspect. So, given I'm like a pit crew with wheel bearings and luckily I had a spare bearing because I f**ked up my parts order, I decided to just smash it out. Got the old one out in about an hour. So much easier when the parts haven't had a chance to rust together yet. 😂 And, well, found the problem.    In the second pic at about the 8 o'clock position, you'll see what I think is the tip of the old sensor.  The new sensor has definitely been rubbing but it's all intact, just a little shiny so I'm hoping it's fine.  The car brakes perfectly now and no errors.  I think the job took about 2.5h in the end. 👍🏻 I really appreciate the help in here as usual. Thanks guys.
    • Chupapy
      Help please! Hole ontop of box?

      By Chupapy · Posted

      I was only looking because I saw some drops on the ground but it wasn't alot. Recently had it serviced will ask the mech to confirm. Find it strange that it looks standard though, can see in another photo of a random box 
    • Duncan
      Help please! Hole ontop of box?

      By Duncan · Posted

      So...not sure if you know if that has always been there or why you went looking. It could be old damage from a clutch explosion, or even just the gearbox got dropped somewhere along the line. Basically, you should seal it up to stop oil and dust getting into the bellhousing, but it doesn't matter too much and is not structural. I'd suggest something like a glob of JB Weld. BTW what gearbox oil are you running, I would guess the breather has been spewing it everywhere.
    • Chupapy
      Help please! Hole ontop of box?

      By Chupapy · Posted

      Hey Duncan thanks for your reply. Sorry mate I know the photos are shit.  Took another photo for reference. Seems the casing does have a hole in it looking on the net, fluid seeping out. Added a photo   
×
×
  • Create New...