Jump to content
SAU Community

Recommended Posts

Rob, The garett turbo's are great, you just have to understand what effect they will have, and don't bolt one on randomly. HKS have slightly better trims but value for money the garett's win.

R33 Impul,

I have a friend who is custom making my manifold, but there are a number of people around town who can do it.

See'ya:burnout:

HKS don't give out the exact sizing or trim of there turbo's, therefore you would have to pull one apart to find out. I don't think comparing one turbo to another is very useful, just buy the one that will do the job. I am thinking of the GT3040, as it will be much cheaper than the HKS GT3037S.

See'ya:burnout:

Originally posted by rev210

The HKS turbo's are made by garret. If you can measure the HKS componets you can make your own 'identical' down to the HKS badge.

We know :P

But HKS design there own wheels and cores with Garrett housings so u cant make your own HKS turbo unless u could get an exact HKS replica wheel..

Anyway back on track......

Are trust turbos water cooled?

There is no way you can make an HKS turbo out of Garrett parts.

Garrett supplies the parts for HKS which are different to Garrett retail parts itself. There's an agreement between Garrett & HKS that Garret will never provide those HKS-specific parts to others except HKS alone.

Lots of ppl tried and they failed to get the same power out of retail Garrett parts. HPI magz also confirmed this can't be done. Get a genuine HKS one is the only solution. This is the way HKS protects their business.

Guys, if you are chasing a HKS turbo, I picked up a brand new GT3037S56T from http://www.fvej.com/perform.htm and it cost me $2700 delivered to my door.

Absolutely brand new - still had all the tape/plastic intact.

As you can imagine, I am pretty stoked, thought I'd put the word out as they told me they are pretty keen to get into the australian parts market.

Yeah I am pretty wrapped - I was going to get one of Grant's, but he got back logged with the e-mails and this one came up before he replied - about $100 more expensive - couldn't resist as the new price on the GCG website is $5880.

Will let you guys know what its like when its in, but it will be a couple of months yet still got plenum, manifold, injectors, headwork, etc to go first.

Steve

GTS-t VSPEC,

I am pretty sure that they dont come up too often at that price. I asked what was available and first off all he had was a few (about 4 or 5) different TD06s. Then this one came up so I grabbed it. Might be worth dropping him a line, let him know what you are after and asking him to keep an eye out.

I'm not even 100% that this will be big enough now - seriously thinking an RB30 conversion will be the go - it might be just a little on the small side? Just seems a shame to get it so cheap and then not even give it a spin.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...