Jump to content
SAU Community

Recommended Posts

Prior to this R33 GTS-T (auto) I used to drive a VS commodore which was about 100 KG heavier... now when going down the hill the VS just rolled like crazy picking up speed. The R33 which is lighter, doesnt roll well at all...Infact the only time it rolled good was when I chucked it into NEUTRAL (i heard its bad for tranny though).

Is this OK or? Cos i feel i could be saving petrol money if it rolled better.

The car is stock with stock wheels.

Also can anyone explain to me whats the go with over drive? I got cruise control and when i turned it off while cruising on 100 KM/h the revs jumped from 2.5 K to over 3.5 K and it slowed the car down so i turned over drive on.

Cheers

Edited by Sir-D
Link to comment
https://www.sau.com.au/forums/topic/112115-rolling-down-the-hill-in-r33/
Share on other sites

overdrive is a "4th gear"

so u drive around looking for hills to "roll" down to save money on fuel? Sorry im just trying to understand exactly what your getting at here thats all.

Rolling will mean u will sit on the brake more and wearing your brake pads quicker?!

overdrive is a "4th gear"

so u drive around looking for hills to "roll" down to save money on fuel? Sorry im just trying to understand exactly what your getting at here thats all.

Rolling will mean u will sit on the brake more and wearing your brake pads quicker?!

So i should always have over drive on ye?

no i dont look for hills :( its just whenever im rollinw down to the traffic lights that are about to turn red i still have to gas it a bit otherwise i lose all my tempo, the commodore had over 270000 KMs though, this one has 44000. Just trying to work out how i could make it roll bit better.

So i should always have over drive on ye?

Yes. It saves the most fuel and for power its okay because the car will know when you want to fang it and switch off overdrive itself.

I have only turned it off for dyno runs.

It rolls worse? Its actually ilegal to have your car in neutral while moving as its classed as not being in control of your vehicle.

As others have stated overdrive is 4th gear. Its the same as rolling down a hill in first in a manual unless you put your foot on the pedal you will only roll at a certain speed.

It may be related to the TPS - Skylines in general cut fuel to the injectors when the throttle closes and the engine is above about 1200 rpm. The Commodore might not do this.

I know my R30 only does the fuel cut above 3200 rpm, so it rarely cuts fuel on throttle backoff. As a result, it tends to drive down hills. My R32 does do fuel cut, so it basically maintains speed down hills. It's almost like an engine brake.

Having both auto Skyline and VS dunnydore, so I know what he's talking about.

The VS auto, especially around town, doesn't lock up at moderate speeds, so when you roll downhill, you notice the tacho drop down to a fast idle. (Really great for getting booked by the coppers hiding at the bottom of the hills.)

The Skyline locks up at a much lower speed, It's quite noticeable when you swap from one car to the other. Makes you think you're still in 3rd, but at least you don't have to roll downhill with the bloody brakes on.

Having both auto Skyline and VS dunnydore, so I know what he's talking about.

The VS auto, especially around town, doesn't lock up at moderate speeds, so when you roll downhill, you notice the tacho drop down to a fast idle. (Really great for getting booked by the coppers hiding at the bottom of the hills.)

The Skyline locks up at a much lower speed, It's quite noticeable when you swap from one car to the other. Makes you think you're still in 3rd, but at least you don't have to roll downhill with the bloody brakes on.

Thanks dude. Commodores arent that bad though :laugh:

  • 3 weeks later...

I think it's mostly due to the gear ratios. The Skyline auto does around 3000 rpm in top gear at an indicated 110km/h, while the Commodore is doing around 1800 rpm in top gear at the same speed.

We've had a pile of Calais' over the years (company cars) and I swear, every gearbox has been programmed differently. There is a large hill near our place where you start out at about 90km/h and by the end in the Calais you will be doing around 115km/h, but in the Skyline you would probably only hit 100km/h if you're lucky. In the first Calais' the revs used to hold at whatever they would have been with the accelerator depressed in top gear, then a couple of cars after that used to drop revs to idle, then raise them back up, then drop, etc. Then another one would just drop them to about 1200rpm all the way down the hill. The one we have now (5 spd auto) seems to keep revs as if you are in top gear, like the first cars. Dunno why they keep on changing, but I suspect they're to do with how the transmission logic is programmed.

Oh yeah, I had a point to all that... the cars that kept the revs equal to top gear (locked torque converter?) seem to roll the best. The Skyline seems to drop revs slightly when you lift your foot off, so I suspect the torque converter becomes unlocked, so possibly that puts extra drag on the engine, and combined with lower gearing (more engine braking because of increased revs), that may account for the extra rolling resistance?

Also, just out of interest, the Calais has an instantaneous fuel consumption feature on the trip computer, and all cars except the ones that used to raise and drop the revs intermittently read 0.0L/100km all the way down the hill. Dunno if that's actually true or not, but it sure would be nice! :(

Also, I just keep overdrive turned on all the time. That's certainly the way to go if you're trying to save fuel. I find the car's fine at all speeds like that - the transmission seems a lot more responsive than any of the Calais' we've had, even the newest one with the 5 spd auto!

oh... oh dear... over drive !! lol, do the 1994 r33 gts's come with an over drive? Cause for that Newcastle Cruise I was sitting on 3k+ the whole way and back haha, how do I turn it on/off??

theres a button O/D on ur auto shifter...

when its on it should not glow on ur dash board... when its off it will glow OD or overdive.

post-23785-1146094274.jpg

oh... oh dear... over drive !! lol, do the 1994 r33 gts's come with an over drive? Cause for that Newcastle Cruise I was sitting on 3k+ the whole way and back haha, how do I turn it on/off??

I assume the gear ratios are the same for the S1 and S2 auto's, so I'd say you'd already have the overdrive on if you were doing around 3000 rpm at around 100 km/h. You'd be doing over 4000rpm if you had it off!

Damn I wish they had a 5th gear so you could cruise at 2000 rpm down the motorway - would be quieter, save fuel, less wear and tear... I know you'd have almost no torque at that speed but the auto's kick down pretty fast on light throttle so that probably wouldn't matter. Oh well, I can only dream... :devil:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was using the wiring diagram I have So 12.74V is coming into the rear Fuel Pump relay as I measured.  When I turn the key to ON im getting 0.6V to the Fuel Pump plug; which i assume is backfeed voltage and doesnt include the 12V from ignition power.  The rear relay is working and being triggered.  From the diagram I clearly see the rear relay 80 = Rear Relay going into the Body/H loom (R-27) 27 = Fuel Pump plug going into the Body/H loom (T-20) 40 = Short Connector (R-27) I'm reading 12.74V on the blue/black wire which is the power for the Fuel Pump   From this diagram I can see the Ignition relay goes into the front and up to the ignition  2 = Fuel Pump Relay <1M> (R-27) 37 = ING Relay <1M> I started from the pump using this reference Which the way I read it (referencing Nissan wiring color codes) is: Pin Wire Color Function 1 B/P (Black/Pink) Ground 2 L/W (Blue/White)        ECU Trigger 3 SB (Sky Blue) Fuel Pump 5 L/B (Blue/Black) 12V Constant Tested SB to SB on Fuel Pump for continuity - confirmed Tested negative on Fuel Pump to 12V battery and L/B - confirmed 12V Pulled the relay putting 12V between Pin 1 & 2 and testing continuity on Pin 3 & 4 - confirmed relay   So that has me looking at this part of the circuit to understand whats happening here...and im still confused. From best I can tell; the disconnect is back to my previous diagram; between Ignition Relay and Fuel Pump Relay...which yet again; afaik is where the immobiliser should.    Thats what I was trying to explain to GTSboy; im not trying to fix it myself; yet I seem to have to get a Masters in Electrical Engineering (while im busy doing my actual job of DevOps & Cloud Engineering) somehow.  I just wanted more expert opinions; or more so that what I tested is correct and proves it to something around that area; to go back to the alarm tech (for a 3rd time) that he needs to fix it. He keeps telling me its not the alarm. He lives on the complete other side of the city so i understand not wanting to make a trip but as I said before if its the alarm it should be up to him to fix it. But he's adament its not; even though I pointed out the FP was immobilised through the original alarm. To my mind; it seems that the ECU is sending the signal; but the ignition is not getting 12V down the line.       
    • Maybe also really stiffly sprung track cars. Get the inside wheel up in a corner and all the fun stops. Also me sometimes (rarely) when I have to stand on the brake to convince the diff to drive the wheel that is still on the ground when I'm trying to diagonally get over severe driveway entrance, etc.
    • I feel like I'm missing something. You had an authorised installer come out and install a new alarm. Post install the car doesn't start, and you aren't getting the installer back to fix what they did wrong?
    • So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
×
×
  • Create New...