Jump to content
SAU Community

Recommended Posts

This turbo is a monster with a 1.15 A/R exhaust, but has anyone done it and what lag can be expected? Boost to kick in at 5k or a bit better than that?

Advice appreciated.

FMIC

Haltech

Stock internals

3" full exhaust etc.

would only be running 1 bar.

Link to comment
https://www.sau.com.au/forums/topic/113094-gt42-on-rb25det/
Share on other sites

I bolted on a HKS T51R Kai BB for shits and giggles to a stock RB25 longblock. Had a Greddy plenum/115mm intercooler/PowerFC.... was a rocketship i tell ya! Had to flatchange gears to get some boost into the system, made next to no boost in 1st gear. Only ran 9psi, was a bit timid with boost at the time. Had to bump up the rev limit on the dyno to 8500, when it hit boost at 7k it fried the tyres.

Oh, made power for alot more than 2 minutes. Took it off out of frustration (and had another turbo to try out). Even tried out circuit racing at Eastern Creek with it, Roy and I couldn't stop laughing at it (well, until it fouled the plugs and nearly had to be towed off).

Visual appeal was at a maximum though.

post-4735-1144675020.jpg

Link to comment
https://www.sau.com.au/forums/topic/113094-gt42-on-rb25det/#findComment-2085457
Share on other sites

http://i69.photobucket.com/albums/i70/tjomi/DSC01157.jpg

Was going for the 42, but I chickened out because it scared me unpacking it.

Went for littlebrother GT40, and that one even looks too big.

The little one is a 600hp Precision turbo!

I`ll give the GT40 a try.750hp rating. Wiseco/Crower internals.

Link to comment
https://www.sau.com.au/forums/topic/113094-gt42-on-rb25det/#findComment-2085602
Share on other sites

It was only by chance that I found one so I figured I would ask.

I really want a GT30/40, GT35/40 or a HKS 3037S something equivalent which is proven on the RB25's.

But thanks for the input, like I said appreciated.

Link to comment
https://www.sau.com.au/forums/topic/113094-gt42-on-rb25det/#findComment-2085647
Share on other sites

It wasn't a lag monster, it was a Skyline built for cruising. You could call it a Skying.... or a Cruiseliner? heheh

Those guys that were with me the night you gave me a lift to the Swans game still pull their d1cks over how it went, and more imprtantly how it sdounded when it spooled and hit boost.

It was so cool, the sound alone was worth every second you had to wait to boost.

Link to comment
https://www.sau.com.au/forums/topic/113094-gt42-on-rb25det/#findComment-2086187
Share on other sites

This turbo is a monster with a 1.15 A/R exhaust, but has anyone done it and what lag can be expected? Boost to kick in at 5k or a bit better than that?

Advice appreciated.

FMIC

Haltech

Stock internals

3" full exhaust etc.

would only be running 1 bar.

I think its sufficient to say that an 800Hp turbo is a long way out of place on an RB25 , it would be extreme on an RB26 and laggy on a street driven RB30DET .

If you go this way and I strongly advise you don't , use the HKS version which is called T51R as it uses a smaller trim turbine than the Garrett marketed GT42R ie 76T vs 84T .

Very very laggy , very expensive and very likely to destroy your RB25 . Why bother .

Cheers A .

Link to comment
https://www.sau.com.au/forums/topic/113094-gt42-on-rb25det/#findComment-2086314
Share on other sites

If it were me on a std RB25DET I would do the HKS GT3037 in 52 comp trim or ask GCG if they can make a similar combination up for you . A lot of people find the GT30R (the real one which is same cartridge as GT3037 56T) is laggy and you have to push it to get good squirt which is a pain in a road car . Small AR turbine housings only make them surge so that 52T compressor is a must and makes 40lbs airflow in .50AR TO4E cover so 400 should be no prob .

A bit OT but we need Garrett Japan to make GT30 and GT35 turbines in smaller trims than 84 , the current GT40R uses a 78T and the High Kost Spec GT42R (T51R) a 76T turbine .

Cheers A .

Link to comment
https://www.sau.com.au/forums/topic/113094-gt42-on-rb25det/#findComment-2087218
Share on other sites

if it's any use as a comparison, i have a GT40 with a 1.34 A/R rear housing on my RB30 DET. standard cams, custom plenum and exhaust manifold.

1st gear: lucky to see 4psi of boost at 6000rpm. full traction.

2nd gear: 10psi around 4800rpm (hard to tell) lots of tyre frying. goes from 70km/h to 130km/h in the space of about 1 second. this gear feels roughly three times as fast as first did.

3rd gear: 10psi at 4000rpm. traction is borderline. very fast gear up top past 150km/h.

4th gear: load it up and you'll have 10psi at 3500. by then you're doing close to the sound barrier anyway so you better stop quick.

on a 25 even the GT40 with smallest rear would be stupid, let alone the one i have.

p.s. makes great noises though, this turbo!

Link to comment
https://www.sau.com.au/forums/topic/113094-gt42-on-rb25det/#findComment-2089602
Share on other sites

Photo-0053.jpg

Precision makes smaller exhausthousings for the GT40. This one is A/R 0.81 with 69mm outlet.

They call this turbo GT4067R. Rollerbearing core. 750hp rating. 1.5bar/22psi at 4800-5000 rpm with some good cams. I`ll post my dynopaper when done building/ mapping.

Link to comment
https://www.sau.com.au/forums/topic/113094-gt42-on-rb25det/#findComment-2089704
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...