Jump to content
SAU Community

Which Engine Oil ?

Mid_Nite_R33

By Mid_Nite_R33,
in General Maintenance

 Share

Recommended Posts

  • Replies 92
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Bunta Grand Master

Bunta

Posted
Posted

Hi guys I thought I should add a story that I have

Recently my car started losing oil pressure, It was fine on cold start but as you drove around the pressure dropped to almost nothing and I was using a heap of oil as well, I was thinking the worst, till I read TO4GTRs thread about keeping that RB alive.

I had Motul 10w40 turbo light in the car and as the temperature built the oil simply couldnt cope and broke down becoming too thin for the pump to push properly

I changed to penrite 5w60 and problem solved so thnaks to dave for pointing me in the right direction, the penrite is about $20 cheaper too!

  • 4 years later...
Ultimategtr Proficient

Ultimategtr

Posted
Posted

What are peoples thoughts on PENRITE 5w60 Fully Syn?

I just ordered mine $120 for 5L. Guy at Supercheap showed me this:

http://royalpurple.com.au/article_images/oil_test_article.pdf?ptl=hot_rod_article.php?ptl=articles_oil_supplement.php

PDF file showing a test run by a magazine. Unsure whether to believe it or not(could be a big marketing ploy). Motul didnt do too well in that test, and neither did Mobil/Elf..

Galois Veteran

Galois

Posted
Posted

For anyone wanting more info it's all covered in the oils sticky whistling.gif

I used motul 8100 xcess, and loved it, until sougi s6000 came into my life. But that's dead and gone now sadly. The nulon "fully synth" was pretty good for a grade 3, cost a bit though when 4100 turbolight is cheaper.

Not sure if it's the same for gtr's, I'd imagine it is, but 10w40 is usually about right for aussie conditions with the normal number of kms on it.

There are a few conditions that have to be met by the viscosity of the oil, and it's all compromises:

-On start up it has to be thin enough to be pumped quickly to moving parts, yet thick enough to provide decent protection when there.

-You want it to be thick to provide decent protection for valves and cylinders, but thin enough to drain from the head to the sump properly.

They're the two big ones. 10w40 is usually accepted to be adequate for australia. The original nissan oil was 7.5w30, but many kms have been done since then and, more importantly, the weather conditions are different here.

(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted

How about Penrite Sin 5 (5W-60)?

I have a standard R32 GT-R, probably has like 120,000 km

Nissan recommend 7.5W - 30 in their books.

+ the R32 being engineered in the late 80's to early mid 90's, it would most probably be a Mineral Based engine oil.

I have used:

- Martini Racing 10W - 40, Full Synthetic = Very nice!

- Valvoline 20W - 50, Semi Synthetic = Bit too "thick" and car ran sluggish.

- Shell 15W - 50, Semi Synthetic = Was ok for the first 1000 kms then turn to shit.

- Mobil Synthetic S 10W - 40 (2000 X 2) Semi Synthetic = Best so far from what I have used and just before an oil change the car still runs well, once changed = Very smooth.

My mechanic has recommended Mobil Synthetic S and the car is running fine.

I think the Mobil has the closest viscosity to what the R32 GTR should run, but everyone has their own personal preference and recommendations.

Different cars will have different recommendations + if you car is modified (Mild to Heavy) and having internal mods done, you'd run a Full Synthetic as the engine will have different tolerances to stock and lightly modified cars.

Ultimategtr Proficient

Ultimategtr

Posted
Posted (edited)

Just changed my oil today. Oil pressure on cold start up is down to around 5bar(7bar before). I used to run Elf fully sun 15w50(I think). Im also using a Veruspeed Nismo filter as well.

I noticed the engine was more responsive. I guess I'll keep an eye on it.

EDIT - I used Penrite 5w60 Fully syn oil. Bloody exp - $130/5L.

Edited by Ultimategtr

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...