Jump to content
SAU Community

Recommended Posts

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...
  • 1 month later...

UPDATE

Have not done alot been working and in new zealand. this is what I'm up to:

Picture003.jpg

Picture006.jpg

Picture021.jpg

Picture027.jpg

Picture030.jpg

Mags are black. ABS and so on is painted. Trans cooler in. Also I have more and more engine parts in my room. Pick the engine up next week and will be putting it in on the week end if all go's to plan will upload some photos then.

Let me know what you think.

Edited by R32 _ULTIMATE_WEAPON

cheech bro, look at the props for your baby and her paint.. hehehhe

The blue stuff looks good bro, was a little worried that the choic was bad when not getting a met blue, but looks good G

Now gimme my guns back,lol

Ya making me look mad... hahahha

Edited by kezza

AzzurrA go for it just look what you can do

Kezza come get your guns any time and I still have all them other parts for you to. I'll need to get my engine jack back to pick up the engnie getting that N1 water pump and then it's all go to put it in.

Year keith car is looking good will be good when we all finish it coz then we can move all the sh!t araund in the shead so we can get my skyline back in there. She gets abit cold out side all the time lol.

I thinks the best part of this project was when u and kezza got relly f##ked off the paint fumes and started runing around the house makeing funny noises haha (hi as a pie)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...