Jump to content
SAU Community

Recommended Posts

actually just use your mouth, yelled out the noise and you will be sweet!!

BOV and pods are the latest generation of wanky factors nowadays in this car scene, just remember BOVs dont do shit! i have a factory one on mine and it actually works better. so what u want the f**ken noise for?

oii oii, I'm getting trashing of my life, gone doing assignment..

Yes of course I meant Atmospheric Blow off Valve (BOV). The plumb back makes next to no noise at all and in this context, "sound" is the key.

Atmospheric BOV does increase fuel consumption just do a search within this forum itself. They also causes the car to stall if set incorrectly.

If GTT factory claimed flywheel hp is 206. Then my car must be smoking weed to be able to achieve 200hp at the wheels, stock. While at it, what is the factory rated power for GTR? 206 as well isn't it? This is because of a gentlemen’s agreement between Jap cars manufacturer (Wikipedia, 2006)

Also 206 figure at the flywheel is not in the unit of Hp...It is actually 206KW at the flywheel or 280hp.

“A (now-defunct) agreement between the major Japanese auto manufacturers to limit the maximum advertised engine power of their cars to 280 PS (206 kW or 276 hp).” Wikipedia,2006

Quoting myself “also apparently stock GTT suppose to have abt 206hp”

“Apparently” means it seems that or seemingly (Cambridge, 2006). I’ll explain further: “meaning I am not sure”

A comparison between my Dyno result and rumours that have been going around (206hp at the wheel, not flywheel!!) cannot be established as a definite implication

If everyone choses to be so specific a plumb back valve is not a blow off valve...it's termed a bypass valve (Hide, 2006)

“Blow-off valve (BOV) / Dump Valve / Vent valve

This valve type features an adjustable spring design (spring in compression) to keep the valve closed under idle, cruise and boost conditions (eg 0.5 bar). Only at sudden throttle lift-off (eg 0.8 bar) does the valve momentarily open to vent / dump the pressurised air directly to atmosphere through a specially designed orifice (and wooshtssh).

Compressor bypass valve (CBV)

In the CBV case, pressurised air is returned to the turbo compressor inlet for reuse, instead of being dumped to atmosphere. The bypass valve is open under normal low-load engine running conditions, and closes firmly when positive (boost) pressure is present in the inlet manifold (or plenum chamber). When on-boost and changing gear (throttle lift-off), a sudden lower pressure condition is created in the manifold and the valve is pulled open again, directing pressurised air back to the turbo inlet.” (Hide,2006)

Last note:

Do your own research before believing in whatever people type in forums.

Jesus…there I’ll go back to my assignment

Reference

Wikipedia the free encyclopedia: Nissan Skyline, 2006. Retrieved May 3rd, 2006, from, http://en.wikipedia.org/wiki/Nissan_skyline

Cambridge Dictionary Online: Apparently, 2006. Retrieved May 3rd,2006, from, http://dictionary.cambridge.org/define.asp...=3513&dict=CALD

Hide, A. Compressor bypass valve (CBV) / Turbo Blow off valve (BOV) / Dump valve / Vent valve, 2003. Retrieved May 3rd, 2006, from, http://wwwrsphysse.anu.edu.au/~amh110/Tech...w_off_valve.htm

Wikipedia the free encyclopedia: Gentleme’s agreement, 2006. Retrieved May 3rd, 2006, from, http://en.wikipedia.org/wiki/Gentlemen's_agreement

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...