Jump to content
SAU Community

Recommended Posts

Now that sounds better. I fill my car up to the maximum limit it can hold. (65L), i drive it all the way untill it literally hits the end of the empty line, i go to fill it up, it only takes about 35-40L. Its still got around 20L left of petrol yet it says its empty. The light doesnt come up or anything, im just too scared to risk it incase. Ive heard this is pretty common in skylines, anyone know? Any possible fix to this if any?

It's pretty common on most cars, I think it's a design thing, to stop people running out of petrol. The common thing to do is fill it up when it gets low. Why do you want to run the tank dry? Low fuel warning light usually comes on when the tank has ~10L of petrol left, but this varies with cars.

I've put a new fuel sender in the tank and it hardly changed. The light doesn't come on until the needle goes just past the 'E' it's about 10L left when your needle drops about 1mm under the 'E' on the factory gauge.
Best only do that if you need to change a fuel pump.

You won't find a car (with a working fuel gauge) that doesn't have the fuel light come on with about 10l left in the tank. This is so when the light comes on you have enough fuel to get to a servo. No point having the low warning light come on and the having it run out of fuel 5 seconds later.

You won't find a car (with a working fuel gauge) that doesn't have the fuel light come on with about 10l left in the tank. This is so when the light comes on you have enough fuel to get to a servo. No point having the low warning light come on and the having it run out of fuel 5 seconds later.

I know, and i agree it would be really stupid for it to come on with only 5 seconds left of fuel. I just find it odd that it says im on empty, yet i fill it up and it only takes about 40L of petrol, thats still 25L of petrol left. One day i drove it around for a couple days when the needle was on empty. Eventually i went to fill up because i thought the fuel light would of turned on by now, so i thought maybe my car doesnt have one. It only took 40L, i was thinking it was going to take atleast 55L of petrol before being completely full again. So thats why im thinking i need a new fuel sender but thought id better ask the people on these forums before i waste money on something not needed. Im not complaining that much though, better safe then sorry, just that fuel reading is very misleading.

Now that i know the fuel warning light comes on with 10L of petrol left, im going to top it all the way up and drive it until the light comes on and see how much km i get out of 55L of petrol. I guess im hoping for atleast 450km out of 55L.

Edited by Gw2
  • 2 weeks later...

There is a few things you can do. First, reset your odometer everytime you fill up, then just run it till the needle is pretty much spot on the empty line. Then take note how many litres it takes to fill it. Then you can work out your average economy and then work out how much further you could drive based off how much is generally left in the tank when the needle is on the empty line. This method will give you an accurate way to calculate how much fuel you've used and how much is left down to a few litres. Much more accurately than any fuel gauge as they can work in funny ways depending on tank shape. For example, I've had 2 cars where I could drive close to 150kms before the gauge moved from full, yet my current car will be down to 3/4 after that distance, but yet the last 1/4 (from 1/4 to the empty line) I can do close to 300kms.

But I don't see what the problem is really. Just fill up when you want/need to. It makes difference to whether you fill up with 20l left or 10l left. Your economy will be the same, and in the long run it still costs the same.

Yeah, plus 4cyl rego is cheaper than 6cyl rego. I work between 4 and 6 days a week and drive about 125km (round trip) to and from work everyday. The Commodore got about 8.8l/100kms, the mirage gets just over 6l/100kms (best I've gotten was 5.7l/100kms).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...