Jump to content
SAU Community

Recommended Posts

  • Replies 125
  • Created
  • Last Reply

Top Posters In This Topic

i have been holding this back but feel i can say it now that the group buy is over:

i bought a brushed stainless steel bezel for $30 incluing delivery fron the USA to australia

great quality, fits perfectly, and looks great... also comes in brushed aluminium and chrome

for those that can't wait for another group buy, and for half the cost :P

http://cgi.ebay.com/ebaymotors/Nissan-Skyl...sspagenameZWD2V

post-2094-1153659308.jpg

i have been holding this back but feel i can say it now that the group buy is over:

i bought a brushed stainless steel bezel for $30 incluing delivery fron the USA to australia

great quality, fits perfectly, and looks great... also comes in brushed aluminium and chrome

for those that can't wait for another group buy, and for half the cost :wave:

http://cgi.ebay.com/ebaymotors/Nissan-Skyl...sspagenameZWD2V

Sorry to burst your bubble warren, but they look cheap

for one, they dont have chrome rings around the dials. And all the R32s from 1989 to 1993 are not the same bezels set!

Shit, i could get some flat sheet from work and trace it all out and make them better than that!

But no, I dont make any money out of this so Feel free to get the cruddy looking ones that are not even made in japan! Hahahha $30

All i have to say is YOU GET WHAT YOU PAY FOR.

carparkpics016.jpg

Edited by kezza

Warren I have delt with Kezza more then once. I have purchased bezel off him befor along with menny outher items. There is nothing wrong with the product that he is selling on this form and yes i have had a look at your bezel on ebay and find them to be a bit cheap looking.

At the end off the day (as Kezza has said) you get what you pay for. If you are looking for a good quality items the be prepared to pay good money.

That is my 2c any way.

And no i am not haveing a go at you warren I just think this needed to be said.

Ryan

firstly.. i never said that kezza organised a bad product, in fact i never said anything about the product kezza had organised, not about his integrity as a member of SAU.. so relax on the whole "i have dealt with kezza and he is a good bloke" thing, because i know he is, and i was never saying otherwise

I simply pointed out for the people who are asking for a bezel, that there is an alternative way to get them.. that are metal and not plastic, and arrive in only 2 weeks

How can you tell the quality from one shitty picture? its not even a picture of the bezel up close..

i know you aren't making any money out of this, so why do you care what people do? they are free to make a choice as to the product they buy...

oh, and i never said anything about a ring set..

Warren

firstly.. i never said that kezza organised a bad product, in fact i never said anything about the product kezza had organised, not about his integrity as a member of SAU.. so relax on the whole "i have dealt with kezza and he is a good bloke" thing, because i know he is, and i was never saying otherwise

I simply pointed out for the people who are asking for a bezel, that there is an alternative way to get them.. that are metal and not plastic, and arrive in only 2 weeks

How can you tell the quality from one shitty picture? its not even a picture of the bezel up close..

i know you aren't making any money out of this, so why do you care what people do? they are free to make a choice as to the product they buy...

oh, and i never said anything about a ring set..

Warren

No worries warren! just got my back up cause of that! People are intitled to get what they want!

and i stand by my statement. You get what you pay for!

But no worries bud!

kezza

How about a EL group buy??

u read my mind...gof or it Kezza u know I'm in.

I was impressed with these bezels and rings - really good and easy to install and the packaging looked so pro...:P seriously it did.

Edited by khunjeng
possible to get els for the 320km/h nismo set?
u read my mind...gof or it Kezza u know I'm in.

I was impressed with these bezels and rings - really good and easy to install and the packaging looked so pro...:mad: seriously it did.

hahahha you guys are funny people! Im not sure, because i know the stork guys dont make the EL dials!

And it was heaps hard to get my set. And that was just a simple ask for a R32 GTS-t.

It waould be alot harder to get all the perfect matches for each persons car.

What i can do is try and get ahold of a suplyer of EL dials and see if they can accomidate for all sorts of line!

That would be the best thing i can do!

BIG NOT THO, EL DIALS ARE ALOT MORE $$$$$$$$$

ill see what i can do!

>_<

Guest
This topic is now closed to further replies.



  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...