Jump to content
SAU Community

Recommended Posts

Started the engine but gear shifter wouldnt move. With engine running, if i pressed the brake pedal a clicking noise could be heard in the consol at the bottom of the shifter, also turning the key on and off produced the same sound. Presumably this is a solenoid of sorts that locks/unlocks the shift lever.ie a steal stopper.

Eventually I got it the shifter lock to open by fiddling (swearing a lot) and stop starting the engine.

It is now doing it sometimes.

Any ideas, or similar problem experienced?

Ive just had another look.

With engine running the shifter button only goes half in. When i depress foot brakebutton goes allway in and operates of until you turn offf. Then process starts again.

Edited by 66yostagea
Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/
Share on other sites

The clicking is the interlock releasing. It stops you putting the car into gear without having your foot on the brake, therefore stopping you leaping into the garage wall, etc.

All auto's have it.

You cannot move the shifter out of 'P' (and 'N', I think) without the ignition on and the brake pedal pushed.

It's not a fault, it's just an auto.

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2135619
Share on other sites

I've been driving the car acouple of months and this is the first time this has happened. Previously i have not been conscious of having my foot on the brake at the time of selecting a gear.Hmmmmmmm?

I must be getting past it and need a wheelchair. Anyway I'm going to see the silver Stager whois just down the road

Edited by 66yostagea
Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2135649
Share on other sites

its a safety measure being developed by the germans. therefore all germans car do that. its to guard against children playing with the auto trans shifter lever and got the car moving. i didnt know the japs adopted this

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2137665
Share on other sites

66yo - I believe you have an S2 in which case the little red button is an overide to the locking mechanism.

If you pass your right arm under your left leg and press the red button with your right thumb while pressing the gear selector nob with your left thumb and pulling backwards, it will come out of P and into gear. In which case you will have backed into the garage wall because you forgot to press the brake pedal with your spare leg.

The red button is useful for moving the gear selector when the ignition is off, and when you're working on the centre console and cant get it back far enough cause it hits the selector.

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2137900
Share on other sites

S1 actually. But many thanks. I looked up j-spec 5724 and saw the red button yyou sreak of. My S1 dosnt have it.

It is interesting what Yudy said about this feature being German. The S! I have is a 1996 model so Nissan have been using it for ten years maybe more.

Do Bommerdores and Found On Rubbish Dumps have this feature?

Another interesting feature that Nissan had on the RMR30 Ti was being able to close the electric windows after the engine is turned off, without putting the key back in.Very handy.

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2139278
Share on other sites

S1 actually. But many thanks. I looked up j-spec 5724 and saw the red button yyou sreak of. My S1 dosnt have it.

It is interesting what Yudy said about this feature being German. The S! I have is a 1996 model so Nissan have been using it for ten years maybe more.

Do Bommerdores and Found On Rubbish Dumps have this feature?

Another interesting feature that Nissan had on the RMR30 Ti was being able to close the electric windows after the engine is turned off, without putting the key back in.Very handy.

66

dont forget though the 260rs its 2nd car i owned which is japamese. I have driven BMWS most of the time until i came to oz. My fisrt car was my landcruise . so... I drove mostly continental cars all my life until recently.

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2139494
Share on other sites

its a safety measure being developed by the germans. therefore all germans car do that. its to guard against children playing with the auto trans shifter lever and got the car moving. i didnt know the japs adopted this

The foot-brake interlock was developed by the Germans, yes, particularly Audi. Americans with less than half-a-brain (most of them, in my opinion) started running litigation suits against car manufacturers for "unintended acceleration." Instead of said Americans taking responibility for their own actions, they blamed the car (a machine, after all) for moving when the gear selector was moved into either Reverse or Drive, causing shock, injury, or - at worst - death as the car lurched backwards or forwards under its own unhindered power...

Audi was the hardest hit in the litigations, and it almost brought them down...

It's not exactly being developed, most of this litigation and the changes to cars happened 20-30 years ago. It's the same reason that early Hyundai's were amongst the first to have the same system on their manual cars, where the engine couldn't be cranked over until the clutch was depressed all the way to the floor.

(See, Hyundai's were good for something - it's a shame that that about covers it...)

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2140133
Share on other sites

Since joining this Forum I am astounded at the details of Auto Enthusiasm that abounds.

A simple thing like not putting my foot on the brake before selecting a gear, has produced a wealth of dispersable knowledge.

We are all the wiser.

Also I think my typing is improving.

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2140188
Share on other sites

Well we all like cars i suppose. Thats why we are into it. But to tell you the truth though i like NA cars better. I think thas where the tech is. dont you guys agree?

For an example the Bmw M5 thats a beast!! The agine is made up of magensium ally and it wiegh no more than 300kg and its a v10!! There goed the niche of the rotary of a lightwieght engine.

But the rotary is still another matter i like it though. Cos i can say my engine redlined @9500rmp stick!! hahahahah

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2140717
Share on other sites

Well we all like cars i suppose. Thats why we are into it. But to tell you the truth though i like NA cars better. I think thas where the tech is. dont you guys agree?

For an example the Bmw M5 thats a beast!! The agine is made up of magensium ally and it wiegh no more than 300kg and its a v10!! There goed the niche of the rotary of a lightwieght engine.

But the rotary is still another matter i like it though. Cos i can say my engine redlined @9500rmp stick!! hahahahah

Hey Yudy,

We all have M5's as well, we keep that talk to the M5 forum though...

:P

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2145746
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If they can dyno them, get them dyno'd, make sure they're not leaking, and if they look okay on the dyno and are performing relatively well, put them in the car.   If they're leaking oil etc, and you feel so inclined, open them up yourself and see what you can do to fix it. The main thing you're trying to do is replace the parts that perish, like seals. You're not attempting to change the valving. You might even be able to find somewhere that has the Tein parts/rebuild kit if you dig hard.
    • Can you also make sure the invoices on the box (And none exist in the boxes) are below our import duty limits... I jest, there's nothing I need to actually purchase and order in. (Unless you can find me a rear diff carrier, brand new, for stupidly cheap, that is for a Toyota Landcruiser, HZJ105R GXL, 2000 year model...)  
    • Murphy strikes again! Nothing at all would have gone wrong if you had the tool kit in the car! You'd have just found the clamp loose the next time you went to touch it...
    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
×
×
  • Create New...