Jump to content
SAU Community

Recommended Posts

Is it worth considering a cheaper run down GTR or should you spend the extra money to track down a good example. I am fairly good with all things mechanical and electrical. I built my LC from a bare shell having nothing at all, not even nuts and bolts to start with. I would find someone to do the motor and gearbox but everything else seems do-able. Am i kidding myself here or what?

You can get R32 RB26's for $4K if you look hard enough.

So long as you go in with your eyes open and give it the once over to make sure there's no major dramas its fine. Just depends how much time you want to spend dicking around with your car as opposed to driving it.

Is it worth considering a cheaper run down GTR or should you spend the extra money to track down a good example. I am fairly good with all things mechanical and electrical. I built my LC from a bare shell having nothing at all, not even nuts and bolts to start with. I would find someone to do the motor and gearbox but everything else seems do-able. Am i kidding myself here or what?

The best advice you will get relating to an R32 GT-R is this:

Buy a good one, not a cheap one.

The difference between the cheap one & the good ones is only a few thousand dollars. This will disapper quite quickly is you need to replace major componentry. To use but one example a new set of brake pads & rotors will cost you about $1500 fitted. You get alot of extra bling on a second hand R32 for $1500...

To use but one example a new set of brake pads & rotors will cost you about $1500 fitted.

You always pay a shiet load more when having people work on your car. You could save $300 on the $1500 price tag by shopping around and buying the parts your self.

The GTR price has dropped but there are still good examples out there, good, clean, stockies for $20k and less it seems. I agree they can be cheap to buy but as long as you are aware that running and maintenance costs can be pretty high then you wont be shocked when the bill comes in. I'm hoping to hold onto mine as I think as time goes on the good ones will hold their value as more get crashed and wrecked.

I have two GTRs. I've own the grey one for 13 months and in that time I've fitted new spark plugs, new battery, new front rotors, new pads all round, new braided brake hoses, new coilovers, its had two services, two dyno tunes, tyres rotated and balanced & a wheel alignment. This car came from Japan in awesome condition with all its books and service history.

In the white GTR I had to fit new spark plugs, a new battery, new upper control arm bushes, new clutch, new tyres, had the air conditioner regassed (twice), a service, a dyno tune, all rotors machined, and new brake pads all round.

Bottom line is GTRs cost money - be prepared to fork some out, especially if you're buying one for less than $20,000.

I've own the grey one for 13 months and in that time I've fitted new spark plugs, new battery, new front rotors, new pads all round, new braided brake hoses, new coilovers, its had two services, two dyno tunes, tyres rotated and balanced & a wheel alignment. This car came from Japan in awesome condition with all its books and service history.

In the white GTR I had to fit new spark plugs, a new battery, new upper control arm bushes, new clutch, new tyres, had the air conditioner regassed (twice), a service, a dyno tune, all rotors machined, and new brake pads all round.

Even with a GTST you have to do those things... the cars are getting old now and need work on the a/c, bushes and general wear and tear items.

Heres a list for my general costs over the last four years and 60,km's

$4,200 for twin plate {os gilken} old one was slipping by 120, k

$2,200 discs and pads all round neeeded doing 120, k

$10,000 N1 turbos required, dump pipes, manifold, gaskets etc. OLd ones leaking oil at 130, k

$200 cooling system flush just in case

$800 Air flow meter 3X pain in the ass $300-$350 for meter and $450 dyno and fault finding plus labour

$1000 front bushes Old 1's nackered at 135, k

$600 rear cradle bushes old 1's nackered at 125,k aluminium cones put in . work better, prevent body roll

$1600 100, k service Due and needed timing belt tensioners replaced.

$800 timing belt tensioners nackered again plus service 135, k fishy 1's werth $400

list can go on and on so when you chuck in water pump ,fuel pump, tyres{7 pair's} plus services at 5,thou intrevals as you can guess lots of dollars any way.

Then theres the mod list hehe exhaust, power fc, intercooler ,pipe work, window tint, stereo, alram and speakers to name a few.

now my car cost $35,000 and is the last of the 32 gtr's being a 1994

so i guess it dosent matter how old it is , they a still bl##dy expensive to have and drive

Bloody FUN drive but :PBJ:

Heres a list for my general costs over the last four years and 60,km's

$4,200 for twin plate {os gilken} old one was slipping by 120, k

$2,200 discs and pads all round neeeded doing 120, k

$10,000 N1 turbos required, dump pipes, manifold, gaskets etc. OLd ones leaking oil at 130, k

$200 cooling system flush just in case

$800 Air flow meter 3X pain in the ass $300-$350 for meter and $450 dyno and fault finding plus labour

$1000 front bushes Old 1's nackered at 135, k

$600 rear cradle bushes old 1's nackered at 125,k aluminium cones put in . work better, prevent body roll

$1600 100, k service Due and needed timing belt tensioners replaced.

$800 timing belt tensioners nackered again plus service 135, k fishy 1's werth $400

Your mechanic obviously lives on the French Riviera and flies here 1st class just to service your car.......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...