Jump to content
SAU Community

Recommended Posts

I dont dance to your tune puppy, However, any time you are up to a hard days graft I pay well. But, i am a prick to work for.

thanks for the job offer, but I already have investments that make money for me and all I have to do is sit on the computer.

Been there. Lawyers are tame compared to lying women.

Lawyers can be the difference in you getting everything or nothing, i know that I would prefer a good unethical lawyer that gets everything than one who's ethical and gets nothing...suppose it depends on how much there is to lose though.

Yeah ill let you drive it, but i get to drive the GTR... :yes:

If you break it i get to keep the GTR... :D

If I break the GTR than you get nothing... :)

i dare say ur car will break before mine, mine being fully built and all :)

P.S u couldnt handle ~750bhp :wave:

thanks for the job offer, but I already have investments that make money for me and all I have to do is sit on the computer.

I guess thats proof that you will never be gay. Too lazy to get off your arse.

thanks for the job offer, but I already have investments that make money for me and all I have to do is sit on the computer.

ahah still going..

Other than a broken GTR of course... :)

shane dnt mind he loves 24month builds

and GTR garden ornaments.

Lawyers can be the difference in you getting everything or nothing, i know that I would prefer a good unethical lawyer that gets everything than one who's ethical and gets nothing...suppose it depends on how much there is to lose though.

Everything. so what. get off yo butt and get it all again. All it takes is work.

thanks for the job offer, but I already have investments that make money for me and all I have to do is sit on the computer.

dude daddy's money dont count as ur money

and be honest matt, how much of the stuff u 'own' has bene purcahed with ur own money?

ye... well i see teh mods took care of that right quick.... wtf was it about ne way???????????

twas a little poll re matt (33niz) and how much of a balla he really is i.e he's a tuff nut oldschooler that's too cool for sau nowadays :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...