Jump to content
SAU Community

Recommended Posts

when are we gonna see the beast Jay?

It gets out and about. Has two mountain runs under it's belt and a trip to Rocky already.

Oh the Supra has 19's now, Ren was complaining my car looked better... :laughing-smiley-014:

ok thats fine with me. i'll just sit back, sink piss, watch bathurst and laugh at you lot trying to pull the motor out by urselves! :D

lol thats cool man, you can do that, i have no problem with that.

rohan, we'll head round to noels after we're done in brisbane aiight? (just spoke to him then)

also cars not making nything over 440hp, even on 23psi. they think the cat's dead

yeah, i guess i cant do that.

Hey Mud you big classy girl, How is the VW??

haven't picked it up yet. arghhh!!!

still waiting on paperwork that should be here today.

I was hoping to have it for Saturday. :D

do you think it would be wrong for me to put my SAU plates on it?

Arhhhh, im back...

Whats this count down you were alking about Liz?

till i finish up at work!

soo what actually happened?

yes, its going to be alrite!!!!!!!!!...i hope :D

the radiator exploded

lol thats cool man, you can do that, i have no problem with that.

yeah, i guess i cant do that.

do u mean u can or u cant?

till i finish up at work!

the radiator exploded

it's f**ked, lol

haven't picked it up yet. arghhh!!!

still waiting on paperwork that should be here today.

I was hoping to have it for Saturday. :D

do you think it would be wrong for me to put my SAU plates on it?

i reckon it would be just to have those plates on it.

man hope you get it.

till i finish up at work!

the radiator exploded

oh the ol radiator exploding technique.

bugger...so what rad you getting?

do u mean u can or u cant?

it's f**ked, lol

yep thats the one. shouldnt be ok to do able to that not for you too.

does anyone know a website that has a map that shows which petrol stations have premium unleaded so you can plan a trip?

maybe fuel watch or whatever that site is...other then that there is a new one that just opened by an aussie company...i will google and look around for yah

nup cant find it lol, cant even think of the name of it.

some guy doing dutton rally was advertising it...it was a yellow evo...cant think of the name.

just try fuel watch.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...