Jump to content
SAU Community

Recommended Posts

Yer should be able to make it to the cruise looking forward to it.. are us northerners doing a premeet?

We have to be there at something stupid like 9am. If you want to meet me somewhere earlier than that bring coffee or GTFO :P

In other words, we can have all the SAU boys meet somewhere and then cruise?

Good people the night is young and the scotch is flowing.... I have tommorow off, hell to the hiz ow

Dude it's like you want me to dislike you, ls1 in a skyline and a day off on a Friday,. FRIENDSHIP OVER!

Moaning all

Morning Cap.

Another wet one! Was going to paint but guess gonna have to do something else.

Rain rain go away come back another day (in a Month's time)

Edited by Ants

Morning Cap.

Another wet one! Was going to paint but guess gonna have to do something else.

Rain rain go away come back another day (in a Month's time)

Mornin', but yer it's wrecked my plans for willowbank drag skids this weekend :( .... The Abomination will have to wait another week before its virgin pass.

AFTER THOUGHT: and next weekend I'm "pit crewing" for my mates burnout car at the Gatton sprints (if the ever unorganised twit can get his cam in and tuned in time :/), so it won't be next weekend either :rant:

Lol. When you want things done there are always stumbling blocks.

Predominantly, these hick ups are caused by people we rely on to get things done. In other words life would be bliss if people actually gave two sh!ts!

Lol. When you want things done there are always stumbling blocks.

Predominantly, these hick ups are caused by people we rely on to get things done. In other words life would be bliss if people actually gave two sh!ts!

Yep like if I knew my Nissan speedo couldn't recognise the Holden input signal would of been nice to know... Or

(Warning rant incoming)

if the parts for my extractors didn't take 3 weeks, or my leads weren't farked, or knew I couldn't use the fly by wire throttle body, or the tail shaft didn't take 3 weeks, or that no one has done a wiring loom diagram up for a 33/LS1, or if they ordered me the right ratchet shifter, or my original loom wasnt completely wrecked, or i knew i had to plate under the shifter and have heater hoses hooked up for the mod plate and In general if everyone that I rely on wasnt a slow lazy fark that'd be great!!! :rant:....

Yep like if I knew my Nissan speedo couldn't recognise the Holden input signal would of been nice to know... Or

(Warning rant incoming)

if the parts for my extractors didn't take 3 weeks, or my leads weren't farked, or knew I couldn't use the fly by wire throttle body, or the tail shaft didn't take 3 weeks, or that no one has done a wiring loom diagram up for a 33/LS1, or if they ordered me the right ratchet shifter, or my original loom wasnt completely wrecked, or i knew i had to plate under the shifter and have heater hoses hooked up for the mod plate and In general if everyone that I rely on wasnt a slow lazy fark that'd be great!!! :rant:....

You should of just dropped in a rb25/30 and none of these things would of been a problem, well all except your butt plug your using as a shifter :P haha

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • For fuelling the Haltechs have O2WB fuel controllers. Very useful for helping tuning VE and correcting for *small* mistakes. Of course if your injector/cam/trigger/sensor data is just wrong (or for a GTT which is not a GT) then you will get impossible reactions to things. I am sure you know this already but the reason people don't typically put haltechs (or any Aftermarket ECU) on GT's is because there's practically no real gains to be had - So this knowledge won't be commonplace.
    • Can someone tell me if the cracks seen in the rear sway bar bushings in these photo's is unacceptable from a roadworthy point of view?  
    • Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
    • For me there is a massive difference in manufacturer or big brand crippled android (Sony, Kenwood etc) vs the sort of thing I've installed here, which is basically just a tablet in DIN form factor with open Android, and the other model of course is mirroring - Android Auto/Carplay. I hate the locked down manufacturer and AA options where they decide what apps I'm allowed to install, including the Launcher but also importantly things like Ecutek (for this car) or Real Dash (Stagea) are not supported. Plus those crippled versions tend to be slower due to both overheads and lower spec hardware. On the other hand, when this breaks I'll likely be in trouble for support....but how is that different to owning an Infiniti anyway
×
×
  • Create New...