Jump to content
SAU Community

Recommended Posts

when thery done the run in tune, I was told it was running 12.6v, and they didn't want to push it.

just checked, is running 13-13.2v.

so, should be all good.

didn't drop under 13.0 for more then half a second.

I wanna go fast.

This is good news

That sounds good. I want to finally give the Gatton sprints a go next year. Have been trying for that one for 7 years to no avail

I want to do Gatton, Leyburn and Noosa sprints next year, depends on timing for other pinny cup stuff though. Will definitely be doing Leyburn again because Mrs family does it every year.

Can't justify it at the moment unfortunately. Tow car/4x4 is higher priority for playing with the 31 next year and I don't drive enough anyway, can't deal with 20k sitting in the garage for 6 days of the week. And then on the weekends I'm playing with the 31 etc so no real point of having one at the moment. All those things and I really want to get an investment property in the next year or 2 so that goes a long way to a deposit etc. Shit happens.

Yeah I loved mine when it was clean, it was just such a bastard to keep it that way. Black will be just as bad but it only shows up dirt badly, won't have to deal with that shitty exhaust stain on the rear bar. When/if I get another one it will be a dark colour. Black or I might try and find a dark blue pearl one.

Yeah I loved mine when it was clean, it was just such a bastard to keep it that way. Black will be just as bad but it only shows up dirt badly, won't have to deal with that shitty exhaust stain on the rear bar. When/if I get another one it will be a dark colour. Black or I might try and find a dark blue pearl one.

The Blue is good. I really need to repaint mine. Really not sure what I would go for.
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...