Jump to content
SAU Community

Recommended Posts

  • Replies 90
  • Created
  • Last Reply

Top Posters In This Topic

If I wanted to attend, how would I go about getting an L2s licence?

Easy as mate,,, join SAU NSW and then download the L2 licence form from cams and your in like flin.

I'm tempted to stick my nose in,,,just to piss Front Bum (great nick) and the best looking GTR that does track days,,, but I have a Goulburn track day 4 days before and a hillclimb at Tamworth 2 weeks after so we will see. I'm starting to think you bums are doing track days that I can't get to.

Jason,,,stoked you got the car up and running again,,, you and I are gonna have some mad fun.

Neil.

Hi Neil cant wait to see you on the track but i hope you dont tell me your still running it in when i go past you a worp speed like every other track day ha ha can put out a tow rope if you like lol

Yes but what if Neil slip streams me we will both pass you GTRJASON.

You coming to this one Neil?

Paul L MADGTR calls me front bum. I think is it because I don't do track days in the wet?

Hi Neil cant wait to see you on the track but i hope you dont tell me your still running it in when i go past you a worp speed like every other track day ha ha can put out a tow rope if you like lol

haha jason is already talking it up! good to see someone with a GTR willing to shoot off at the mouth finally. stick it to neil and john for me Jason. otherwise we'll never hear the end of it.

pussies

your all scared of the na rb30e silvia

the underdog from hell

Pete - it's going to be on the rev limiter in 5th before the pit entry...........

Then again with you driving it's going to be on the limiter everywhere.....

Helis on the hill?

man i hope it rains so i can wipp johns arse with a fluffy sword

Rain is GTR only chance. If it rains enough I will through the anchor out as a handicap and you will have a hope. Or drag fatz RB30 around.

Only a zed with cheap motor in it, have your go. Reground cams cost me as much or less than a night out with fatz, turbo's cost me bit over 2 k for two. Maybe it's the GTR modded Power FC we run that does th trick.




  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...