Jump to content
SAU Community

Recommended Posts

since i got my new car last week, i havnt really had a chance to give it a good run till tonight.

I noticed that there is a missfire/flat spot high in the rev range between 5350ish to 6200 rpm then kicks back in at full tilt. this is 2nd and 3rd. its like a surging feeling... power stops, slowly builds revs then bang back with full power. also after this i noticed it miss firing under all load right thru the rev range under load (10 & 12psi)

did a search and found some things about the coils and spark plugs but not sure if it all applies to a S1 rb25.

mods are fmic, full 3", duel stage boost, kn panel, fuel pump and heavy duty clutch.

I have a S-AFC to install yet. would this be able to point out the problem? or maybe a tune via this could fix?

car was supposedly tuned before and made high 190rwkws... my old one made 193 and this feels a lill faster untill this happens

any thoughts guys?

Link to comment
https://www.sau.com.au/forums/topic/122173-high-rpm-miss-fireflat-sopt/
Share on other sites

Get the safc tuned- should fix it up. Other wise, here's my standard reply...

Are the plugs in properly? - reseat.

Are the plugs the correct heat range? - std is 5. 6 and 7 should also be ok.

Are the plugs gapped to 0.8mm - std plugs are 1.1mm, regapped to 0.8mm makes a sturdier spark.

Are your coil packs old and fcuked? - epoxy old ones or get new ones.

It could be running rich. - ECU adds more fuel than fuel needed running more boost. This can cause misfire. - Need aftermarket ECU or piggy back cumputer and tune.

It could be running lean. -fuel pump not supplying enough fuel to the engine, causing it to ping and the ecu hears this by microphones and cuts/retards the ignition. - need a fuel pump, common in early 33's

Hmm i got exactly the same problem on my rb20, at the same rev ranges. Had an assessment done, was told my pump was fugged and filter fugged, replaced filter and that made it worse, so im pretty sure its pump.. Became more noticeable after FMIC install, which would lead me to believe it was packs. Sucks that theres no easy way to figure out which it is.. When i get a spare 4 or 5 hours ill have to voltage check my coil packs i spose

Edited by r32 gts-turbo

I replaced my coilpacks with some low-k used ones, problem solved.

See the huge thread on repairing coilpacks to try and resolve this issue, otherwise, replace coilpacks with used or brand new splitfires. =-]

2min on teh search told me that it could be teh coils, wanted to know if it applied to 33s.

just did the coil diy fix tonight, took it for a spin, had to big missfires and still doin it as before. goin ot have teh safc2 installed and tuned tomorrow, hopefully fix the prob, if not gona grab my old coils from my other 33...

hope this fixes the prob...

sounds like the stock ECU to me

happens to all of them.

If not, then fuel filter, coil packs, fuel pump... the list gets veeery long :domokun:

arrgh dont say that! lol... my other 33 had a link ecu(useless pos) already installed so i never had to go thru that, will know tomorrow... hope this safc2 is a good as i hear :

mine was just like, carr drriivveE....hit massive boost, then it just feels like something snaps, power dies, picks up again. over..and over...and over

same here. get onto boost and then it feels like someone has turned the key off, then it comes back, starts lighting the tyres up, dies again.

problem solved!!! nova performance newcastle did the install and tune today, cars running much better now and faster :)

just noticed under load there is no knock reading but reads upto 2-5 at idle after a squirt... is this normal??

other than that its like driving a new car :yes:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Why are people so insistent on making dirty water?!
    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
×
×
  • Create New...