Jump to content
SAU Community

Recommended Posts

bit dissapointed.

32 GTR

1st up quick list of mods

rebuilt motor

JE pistons

standard crank and rods every thing else replaced.

To4z a/r 1 rear .70 front

50mm ebay wastegate with 12psi spring

hybrid boost controller electronic

PWR cooler

3.5inch exhaust

power FC

put it on the dyno today to raise the boost from 19 to 25psi

had 403kw.

my boost controller won't go higher than 22.5psi. its maxed out wont turn any more.

my question is should i spend the money on an e boost 2 like my tuner reccomends or will a stiffer wastegate spring do the job?

thanks

Link to comment
https://www.sau.com.au/forums/topic/122507-my-gtr-maxed-out/
Share on other sites

Why are you using a cheap Hybrid boost controller on a car which this amount of work?

ditto on the ebay WG ..

if you want more boost

always try to get the WG's spring as close to the desired "low boost" setting you want, and that shouldn't be far from your MAX boost either ..

allows for the best form of boost control. get a better WG and spring and you wont need a boost controller.

yeah i know. i bought it for my old r31 with rb25det. but couldnt fit it.

then i bought the GTR and it had a greddy profec but it didnt work.

so i had this lying around and put it in.

i was going to have 19psi low boost for street and 25psi hi boost for dyno and drag days.

i thought you couldnt get springs rates this high??

where do i get them?

just bought a new tial external gate

has 1.2 Bar springs in it .

Expensive???

i just want the spring.

swap?

haha

just joshin

hoping that an eboost 2 will keep the gate shut .

had a couple of inconsistant ramp ups on the dyno, varied from 380kw to 420kw on 22.5psi. depending on when the gate would open

Expensive???

i just want the spring.

swap?

haha

just joshin

hoping that an eboost 2 will keep the gate shut .

had a couple of inconsistant ramp ups on the dyno, varied from 380kw to 420kw on 22.5psi. depending on when the gate would open

same thing my ebay one was/is doing, hence the upgrade to tial 38mm

i payed around $500 for brand new tial 38mm.. not sure if that would be big enough for you, think it would. that was with the the 1.2 bar sping .. so 18psi - actually runs 2 springs for that pressure

i posted a thread about sizing etc

here it is

http://www.skylinesaustralia.com/forums/in...opic=43638&st=0

aaron @ sliding performance - slide on the forums is who i got it from, ask him if he can get the springs for you

Why are you using a cheap Hybrid boost controller on a car which this amount of work?

Hybrid is a cheap boost controller? HAH you’re joking right? Its one of the best I’ve seen. Had a comparison on a dyno with apexi, greaddy even that Greaddy one with the screen and remote ect... None of them held the boost as good as the hybrid EBC... Hybrid held it perfectly steady with NO spike or imperfection on the graph and came on boost very quick, others came on boost late and build boost gradually and had little boost spikes. I don't know where you’re getting your sources about a Hybrid EBC because I’ve seen proof on a dyno my self.

I would suggest a stronger actuator sprig like everyone else would say. Personally I wouldn’t go with e boost.

Just my 5c...

Cheers,

Alex.

Why are you using a cheap Hybrid boost controller on a car which this amount of work?

i'd say why an ebay wastegate :yes:

which is the lesser of two evils i dont know... they are both equally as sour as the other

just pull the spring out and stretch it!

You have got to be joking?

Anyway, if your running a 12psi spring, and trying to bleed off to more than 22psi.

Thats madness.

Buy a wastegate that works, boost control is one of the most important things and you go to ebay...

Once you get a proven performance application item, get the gate loading as close as you can to the target boost... ie, you wanna run 24psi.

So simply get springs to 21psi (one 14psi + one 7psi) and then bleed the 3psi off that.

Hybrid is a cheap boost controller? HAH you’re joking right? Its one of the best I’ve seen. Had a comparison on a dyno with apexi, greaddy even that Greaddy one with the screen and remote ect... None of them held the boost as good as the hybrid EBC... Hybrid held it perfectly steady with NO spike or imperfection on the graph and came on boost very quick, others came on boost late and build boost gradually and had little boost spikes. I don't know where you’re getting your sources about a Hybrid EBC because I’ve seen proof on a dyno my self.

Was it on a 400rwkw performance application?

Or a stock turbo'd skyline...

i reckon i know which is more likely

Was it on a 400rwkw performance application?

Or a stock turbo'd skyline...

i reckon i know which is more likely

Have you even seen a Hybrid EBC ??

Not quite 400 but over 300. Catharine Caliro (Drift Cat) has one. Seen it on the dyno my self. I was there while it was getting tuned...

A boost controller has nothing to do with the amount of power the car is making. It only controls the boost pressure its quite simple. It regulates the amount of air passing thru to the actuator / waste gate its nothing to technical. And 25psi is not a great deal of boost for any EBC. I don't think I need to explain my self anymore this is common sense guys.

I just don't like people falsely rating Hybrid EBS's...

Cheers,

Alex.

Edited by 217/r33

This is how one looks like...

Hybrid use's the same solenoid as Haltech boost controllers and I think e boost might use the same one.

The rest of it speaks for it self. Don't judge if you haven't tried :no:

Just my 5c...

Cheers,

Alex.

FULL LIST OF SPECS ARE BELOW....

* In cabin adjustment for high boost and low boost.

* Overboost Feature - Hook up an external switch for adding 10% more extra boost.

Ideal for take off in low boost to reduce wheel spin, switch to high boost after you get traction then turn on the over boost function before the finish line!

Easy to install instructions are included. Very compact in size, so you can install it virtually anywhere in the cabin.

This popular product is the result of constant refinement on the street and track.

Hybrid's full electronic boost controller not only spools up the turbo quicker but also regulates

the boost accurately.

You can purchase the Hybrid Boost Controller in two different configurations:

1. Hybrid Electronic Boost Controller Type 2 to suit MAF (Airflow Meter)

2. Hybrid Electronic Boost Controller Type 2 including a Hybrid MAP Sensor. The MAP sensor version can be fitted to any turbo vehicle and allows for closed loop boost control for even more accuracy.

Hybrid 3 Stage Electronic Boost Controller Type 2

Ask a question...

Best of all, the kit comes with all the parts you need for your install:

* Electronic Boost Control Module

* Electronic Wastegate Solenoid (9 bar / 130psi pressure equalised)

* Bracket for Solenoid

* MAP Sensor (Optional)

* Silicon Vacuum Hose

* Wiring Harness

* Fittings

* Cable Ties

* Pictured Instructions

Supports MAF (Airflow Meter) on the following cars:

* Mazda RX7 FC3S (Series 4, 5) - 13B Turbo

* Mazda RX7 FD3S (Series 6, 7, 8) - 13B-REW

* Toyota Aristo JZS147, JZS160, JZS161 - 2JZGTE

* Toyota Soarer GZ20, MZ20, JZZ30 - 1G-GTE, 7M-GTE, 1JZ-GTE

* Toyota Supra GA70, MA70, JZA70, JZA80 - 1G-GTE, 7M-GTE, 1JZ-GTE, 2JZ-GTE

* Toyota Chaser GX81, JZX81, JZX90, JZX100 - 1G-GTE, 1JZ-GTE

* Toyota MR2 SW20 3S-GTE

* Toyota Celica ST165, ST185, ST205 - 3S-GTE

* Toyota Caldina ST215W - 3S-GTE

* Toyota Starlet EP71, EP82, EP91 - 2E-TE, 4E-FTE

* Nissan Cima FPY31 FHY33 - VQ30DET

* Nissan 300ZX Fairlady Z32 - VG30DETT

* Nissan Leopard/Cedric/Gloria GF31, Y31, Y32, Y33 - VQ20DET, VQ30DET

* Nissan Cefiro A31 - RB20DET

* Nissan Laurel C35 - RB26DETT

* Nissan Skyline R31, R32, R33, R34 - RB20ET, RB20DET, RB25DET, RB26DETT

* Nissan Stagea W#C34 - RB25DET

* Nissan Stagea Autech WGNC34 - RB26DETT

* Nissan Bluebird U12, U13 - CA18DET, SR20DET

* Nissan Silvia S13, PS13, S14, S15 - CA18DET, SR20DET

* Nissan 180SX RS13, RPS13 - CA18DET, SR20DET

* Nissan Pulsar RNN14 - SR20DET

* Nissan Aveneir W10, W11 - SR20DET

* Subaru Legacy / Liberty BF5, BC5, BG9, BD9, BG5, BD5, BH5 - EJ20, EJ25

* Subaru Impreza / WRX / STi GF8, GC8 - EJ20

* Subaru Forester SF5 - EJ20

* Suzuki Cappuccino EA11R, EA21R - F6A, K6A

* Mitsubishi GTO Z16A - 6G72

* Mitsubishi Eclipse D27A, D32A - 4G63

* Mitsubishi Lancer Evolution I, II, III, IV, V, VI CD9A, CE9A, CN9A, CP9A - 4G63

* Mitsubishi Lancer CD5A, CM5A, CK4A - 4G63, 4G93, 4G92

hybrid_boost_controller.gif

Well I know my AVCR spikes like a bitch.... Especially in higher gears

As does the one in my friends car. This is after absolutely ages spent adjusting the duty cycle, response time on the solenoid per gear etc etc before anyone asks me if I tried changing the settings.

Its not the worst controler in the world but I definately would not buy another one. In fact if I could be stuffed hauling it out and selling it and installing a new one would not be in the car anymore!

DK

50mm ebay wastegate with 12psi spring

my boost controller won't go higher than 22.5psi. its maxed out wont turn any more.

Regardless of what EBC you are using, you are bleeding off 10 psi which is simply too much.

Get a wastegate spring for the minimum boost you are likely to run.

My rule of thumb is never to bleed off more than 25%

For example if you have a 20 psi then + 25% = 25 psi

:( cheers :P

PS; I don't believe in high/low boost settings, if I want a lower power ouput I don't push the pedal down as far.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...