Jump to content
SAU Community

Recommended Posts

It may well have been posted on this forum already but if not I just wanted to share the news from the UK.

At Santa Pod yesterday (25/6) John Bradhaw in 'Project GTST' ran a 9.9 backed up by a 10.02

This car has undergone major work over the last few months by Gary Passingham at GT-Art and is still only in the shakedown stages at the moment

You can find lot more information about the car at www.projectgtst.com but the basics are that it is a R33 GTST using a bored/stroked RB25 and running a T51SPL

Still to come on the car is an Xtrac gearbox (standard box was used yesterday :D ) , the NOS has not been used yet either and the suspension still has a lot of development work to be done too

Link to comment
https://www.sau.com.au/forums/topic/123873-9-second-gtst-in-the-uk/
Share on other sites

Just a couple of things.

First, AWESOME work by the projectgtst guys! Car looks and sounds sensational.

Second, Slicks on the back and radial fronts @ 140mph?!?!?!

Lastly, It's not yet the WORLD'S fastest gtst but its getting there quickly.

Well done.

Adrian

From www.projectgtst.com

After much searching I finally managed to find the following information on Drag GTST's.

A) The best 1/4 mile time to date worldwide for the RB25 GTST was achieved by Ryan Quinn from Victoria, Australia. Ryan ran at Calder Park and managed a 1/4 mile of 10.12 secs @ 136.3 MPH !!!

B) The best time worldwide for a GTST regardless of engine spec was achieved by a fellow Australian, Brett Whitbread using a RB26/30. Brett ran at Willow Bank and got a 9.464 sec run @ 150.9 MPH !!!

Adrian

Just a couple of things.

First, AWESOME work by the projectgtst guys! Car looks and sounds sensational.

Second, Slicks on the back and radial fronts @ 140mph?!?!?!

Lastly, It's not yet the WORLD'S fastest gtst but its getting there quickly.

Well done.

Adrian

Keeping the RB25 was a very important part of the project, as is keeping the original rear suspension layout rather than going for a tubbed rear end like a couple of the quick RWD cars have opted to over here.

I will have to confirm but I don't believe the 9 sec GTS i listed was tubbed at all - I think it ran on a 10.5" tyre.

Can you tell me the reason for radial fronts and crossply slick rears? Looks dangerous to me - or am I missing something?

Adrian

I will have to confirm but I don't believe the 9 sec GTS i listed was tubbed at all - I think it ran on a 10.5" tyre.

Can you tell me the reason for radial fronts and crossply slick rears? Looks dangerous to me - or am I missing something?

Adrian

I don't know why John ran that tyre combination, he will be the first to admit that he is a complete novice when it comes to drag racing.

Can you tell us the reason why it is a bad idea to run the radials on the front? I assume the comparative lack of grip compared to a slick should you need to correct it mid strip is the issue?

How good was that.Big turbo.I diddnt think that it was capable of 9s on a 25det.

Doesnt bu5ter run the same in his but with a 3l block 26 head.Though he is in full steet trim.

Brett's hotside is rated at 85 bhp, not 1,000 bhp like the big boy trim.

I don't know why John ran that tyre combination, he will be the first to admit that he is a complete novice when it comes to drag racing.

Can you tell us the reason why it is a bad idea to run the radials on the front? I assume the comparative lack of grip compared to a slick should you need to correct it mid strip is the issue?

Crossply tyres 'wander' as you accelerate down the track and radial tyres don't. What you find is that the back starts to sway as you get faster and faster while the radial tyres on the front track straight and true for the duration of the run.

You end up with an ever-increasing pendulum effect that can end in disaster. Please make sure John buys some crossply front-runners before racing again. Ask him if he noticed any swaying in the deep end that he had to correct.

Over here our regs state that if your cr is quicker than 12.50 and you run crossply (slicks) on the rear, you MUST have crossply fronts.

Brett's T51R is the KAI variant and is rated at 850hp not 1000hp like the SPL in this gtst.

Adrian

Crossply tyres 'wander' as you accelerate down the track and radial tyres don't. What you find is that the back starts to sway as you get faster and faster while the radial tyres on the front track straight and true for the duration of the run.

You end up with an ever-increasing pendulum effect that can end in disaster. Please make sure John buys some crossply front-runners before racing again. Ask him if he noticed any swaying in the deep end that he had to correct.

Over here our regs state that if your cr is quicker than 12.50 and you run crossply (slicks) on the rear, you MUST have crossply fronts.

Brett's T51R is the KAI variant and is rated at 850hp not 1000hp like the SPL in this gtst.

Adrian

Cheers for that Adrian

I think the 'tubbed' issue I mentioned was maybe taken the wrong way, what I meant was a couple of the 'quick' RWD cars over here in the UK have gone for a proper drag set up on the rear end, one in particular is the CRD Supra which runs the 9's but will no longer be allowed to run in the street legal class.

The car will not run in competition again until October so we have a long wait to see how the NOS and sequential Xtrac box will improve the times

the subzero cr was not tubbed, it still ran the factory rear end, then used welded up shock absorbers to keep the camber flat and used the sof side wall of the slick tyre as the suspension. it was well documented inthe zoom article.

Shane, effectively turning the IRS into a live axle.

Shane, effectively turning the IRS into a live axle.

yea thats the idea, i spoke to some suspension people about trying it, but was basically told they didnt want to aid in my hurting myself, there view on it was too dangerous, my car has fortunately worked out to sixty foot quite well so the idea is now long gone.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...