Jump to content
SAU Community

Recommended Posts

Sorry I took off last night, looked at the time and pick up my meat tray :-)

You missed a good night, we're not long home. I'm too tired to post up pics now, so will try to get some up tomorrow.

Some Very nice pics there,

My car sould be ready by friday (the engine build) but it wont be tuned or have rego. Should be on the road the following friday.

:D

PS, I love your GTR Ladybytes sure it at the skid pad and OMG. Looks great in the pics.

Would love some pics with my car next to it some time.

and tuk tuk, are they all your photos? They are great.

The one with the cars under the bridge is very nice.

Edited by BNR32t
PS, I love your GTR Ladybytes sure it at the skid pad and OMG. Looks great in the pics.

Would love some pics with my car next to it some time.

Thank you, I think she's pretty special too :D

You're welcome to come have some shots with us anytime. Always on the lookout for a location to test.

and tuk tuk, are they all your photos? They are great.

The one with the cars under the bridge is very nice.

All the ones Tuk Tuk posted are his work.

I checked out that place in Kingston I mentioned, would be alright, nothing too flash though.

In front of the big garage doors at the Old Bus Depot Markets might be better.

The Old Bus Depot should be good for an early morning or dusk shot as well. Might have to check this one out.

If people started turning up earlier, say at say 9pm I wouldn't complain.

Yeah I agree, but I don't think I can make it this Friday, I have to go to Sydney tomorrow and its going to be a big day - Lets see how I feel when I get home.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...