Jump to content
SAU Community

Re - Installing R33 Gearbox

217/r33
 Share

Recommended Posts

217/r33 Community Regular

217/r33

Posted
Posted

I dropped my gearbox on Sat night to replace clutch and flywheel.

Dropped the gearbox in a couple of hours and replaced clutch and flywheel ok. The car is on stands just at the front of the car, im using a hydrolic jack to push the box back into place but the firewall gets in the way of aligning the shaft into the clutch.

Have any of you experienced simular problems ????

Should i jack the car on 4 stands instead of it being on 2 to get the balance right? Or is there a speacial angle that the gearbox must sit on for it to go back in?

If any of you guys have any suggestions or tips on how to put the gearbox back in it would be greatly appreciated.

Cheers,

Alex.

Link to comment
https://www.sau.com.au/forums/topic/126365-re-installing-r33-gearbox/
Share on other sites
wrxhoon Grand Master

wrxhoon

Posted
Posted

It would be easier if the car was on 4 stands. You have to twist the box a little to get it in the tunnel ( the part where the starter fits has to go up ) then twist it back again. I hope you lined up the clutch though .

217/r33 Community Regular

217/r33

Posted
  • Author
Posted
It would be easier if the car was on 4 stands. You have to twist the box a little to get it in the tunnel ( the part where the starter fits has to go up ) then twist it back again. I hope you lined up the clutch though .
as has already been said you need to twist the box about 45 degress clockwise (when looking from the back of the car) to get it back in.

Thanks heaps for that great info guys, I'm gana give it another try some times this week and hope to get it in. Its such a bastard of a job! I'm going to drop the exhuast this time and get it up on 4 stands so ive got some more room to work. I've also rang a gearbox place and they also said that you need to twist the box so that the starter motor part face's down.

Thanks again for the great input, and thanks to grigor for the PM :D

Cheers,

Alex.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...