Jump to content
SAU Community

Recommended Posts

hey ladz, i was muckin around in my car the other day and i pulled the fuse cover off in the hope i could find one for my antenna and pull it out to stop it from reachin 8km in the sky when it goes up... but all the fuse names are in japanese...

does anyone have a english version of what each fuse is for?

Beef

Link to comment
https://www.sau.com.au/forums/topic/126462-fuse-daigram-in-english-please/
Share on other sites

SEARCH thats what its there for

YEAH RIGHTO "SINISTA"..... I DONT KNOW IF YOU HAVE EVER TRIED TO SEARCH FOR ANYTHING ON THIS SITE... BUT The SEARCH ENGINE IS SHIT... IT NEVER BRINGS UP WHAT YOUR LOOKING FOR... HENCE THE REASON PEOPLE START NEW THREADS ABOUT SOMETHING THAT HAS BEEN COVERED BEFORE... BECAUSE THEY CANT FIND IT FROM WHEN IT WAS COVERED BEFORE...

here is an example, i searched for "Fuse" "Fuses" "Fuse Diagram" "Fuse Instructions" "Fuse Meanings" and this was the result....:

1. How To Install A Powerfc

2. Rear De-mister Not Working

3. Car Wont Start

4. R32 Gtr Clock Fuse

5. Strange Dash Behavior

6. R32 Headlight Bulbs!

I KNOW HOW TO SEARCH... BUT THE RESULTS ARE NOT WHAT I FU**IN WANT...

SO I WOULD APPRECIATE IT IF YOU WOULDNT INSULT MY INTELLIGENCE BY SAYIN.."do a search" because i did and it was useless.......

ok, now that has been said... does anyone have any USEFULL posts/replys?

Beef

Edited by Beef
YEAH RIGHTO "SINISTA"..... I DONT KNOW IF YOU HAVE EVER TRIED TO SEARCH FOR ANYTHING ON THIS SITE... BUT The SEARCH ENGINE IS SHIT... IT NEVER BRINGS UP WHAT YOUR LOOKING FOR... HENCE THE REASON PEOPLE START NEW THREADS ABOUT SOMETHING THAT HAS BEEN COVERED BEFORE... BECAUSE THEY CANT FIND IT FROM WHEN IT WAS COVERED BEFORE...

here is an example, i searched for "Fuse" "Fuses" "Fuse Diagram" "Fuse Instructions" "Fuse Meanings" and this was the result.... :

1. How To Install A Powerfc

2. Rear De-mister Not Working

3. Car Wont Start

4. R32 Gtr Clock Fuse

5. Strange Dash Behavior

6. R32 Headlight Bulbs!

I KNOW HOW TO SEARCH... BUT THE RESULTS ARE NOT WHAT I FU**IN WANT...

SO I WOULD APPRECIATE IT IF YOU WOULDNT INSULT MY INTELLIGENCE BY SAYIN.."do a search" because i did and it was useless.......

ok, now that has been said... does anyone have any USEFULL posts/replys?

Beef

I have a useful post. Please don't blame the tools, they seem to work for everyone else. If you are upset, please find a nice happy medium between calm and off-the-dial-pissed-off. You'll just offend people and they will stop trying to help you.

  • 1 year later...
AFAIK only the S2 R33 have the adjustable height on the arial..

Wow. Old thread but anyways........

My adjustable height switch doesn't work. It always goes on full length regardless of whether i flip the switch up or down.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...