Jump to content
SAU Community

Recommended Posts

the size i carnt quite rember ,but not that big aroung the 215-220 as a rule but does vary and the stock afm runs out at around the same ,so you need a higher resoulution one ie, z32 but you will need a pfc or some form of piggy back setup ie.safc to run the afm, what are you wanting to do with the car and what is alredy done to it, and power goal.

Edited by gtstcoupe

If i'm not wrong it'll be about 140ish rwkw stock as i saw my mate's GTT with just pod and full exhaust ran a 160ish rwkw on the dyno.

Stock injectors will definitely support 200rwkw. It'll be JUST right. Yes with stock AFM as well. Any higher than that, you might consider changing.

I said this in another topic but may be of interest in here as well.

For the reference also the R34 RB25 Neo injectors are top feed high impedence 370cc.

Unsure if you remember or not but on the High Performance Imports DVD's they did a skyline dyno with different mods on an R34GTT.

This engine has higher output compared to R33 model (206kw vs 187kw)

On the Croydon Dyno Dynamics Dyno it pulled the following figures.

1. 100% Stock R34 GTT Car 148rwkw (R33 should be less then this power)

2. 3" Turbo Back Exhaust - 158rwkw (stock cat still)

3. Boost increase to 10psi - 181rwkw (remember R34 has bigger turbine housing)

4. FMIC & 13psi boost - 200rwkw

5. GCG Highflow, 14psi boost + PowerFC - 225rwkw (injectors 100% duty no more boost can be added safely)

Hope that can bring something to convo as well.

So with a GCG highflow along with my PFC and intercooler I could run around 225rwkw with standard injectors, fuel pump, and airflow meter? Do the fuel pump and afm become inadequate around the same time as the injectors?

Edited by Lithius
I said this in another topic but may be of interest in here as well.

For the reference also the R34 RB25 Neo injectors are top feed high impedence 370cc.

I've actually got that DVD with me. The whole process was seperated into 3 parts. They put in the hi-flowed turbo because it blew when they brought their black R34 to the track. Think it's called HPI-34. In the end, the car was running about 260rwkw? or something around that big power region.

Do not run your stock turbo at 14psi ( 1 bar ) for daily driving. :wave:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Try looking at Eibacb/H&R springs Thats what Gary sourced for mine.
    • Hey y'all! I'm curious about how y'all go about widebodying your cars. I noticed that when running a square setup, my front wheels are a bit more tucked in than my rear wheels. Not by much, maybe 5-10mm. This leads me to wonder - when I widebody, should I use narrower front flares and wider rear flares? I found a set of 40mm rear flares that I really like, and was thinking of pairing them with some 18mm front flares, but I don't want the car to look strange. How have others done this? Note, I'm in a sedan. Thanks!
    • And if it was anything other than an auto tranny part, it might be a problem. But seeing as all auto trannies belong in the recycling bin, it's fine.
    • I have an R32 Fenix rad. It is good.
    • All the schemas I can see, indicate your typical setup of ATF 'cooler' (read: heat exchanger) in the bottom radiator tank..ie; https://nissan.epc-data.com/stagea/wgnc34/5413-rb25det/engine/214/ ...but I can prattle on a bit here. These trannies have a thermistor in the sump ~ the TCU reads this and 1. bumps the line pressure up when the ATF is 'cold' and 2. prevents the TC lockup clutch from operating, until the ATF comes up to minimum operating temp (keeps the ATF 'churning' through the TC so it heats up quicker) -- trigger point is around 55C. In these conditions, the engine coolant temperature rises faster than the ATF temperature, and also helps heat the ATF up, which is why it's best to think of the in radiator tank setup as a heat exchanger ; the heat can flow in both directions... ...with these trannies, the 'hot' ATF comes out the front banjo bolt, flows through the cooler/heat exchanger, and returns to the box  via the rear banjo bolt. This gets a mention, due to the wildly different opinions wrt running auto trans fluid coolers ~ do you bypass the in radiator tank altogether, or put the cooler inline with the in radiator tank system...and then, do you put the additional cooler before of after the in radiator tank system?... ....fact is the nominal engine operating temp (roughly 75C), happens to be the ideal temperature for the ATF used in these trannies as well (no surprises there), so for the in radiator tank system to actually 'cool' the ATF, the ATF temp has to be hotter than that...lets say 100C -- you've got 25C of 'excess' heat, (slowly) pumping into the 75C coolant. This part of the equation changes drastically, when you've got 100C ATF flowing through an air cooled radiator ; you can move a lot more excess heat, faster ~ it is possible to cool the ATF 'too much' as it were...(climate matters a lot)... ...in an 'ideal' setup, what you're really trying to control here, is flash heating of the ATF, primarily produced by the TC interface. In a perfect world, wrt auto trans oil cooling, you want a dedicated trans cooler with builtin thermostatic valving - they exist. These should be run inline and before the in radiator tank system ~ when 'cold' the valving bypasses the fin stack, allowing the ATF to flow direct to the in radiator tank heat exchanger, so it works 'as intended' with helping heat the ATF up. When 'hot' (iirc it was 50C threshold), the valving shuts forcing the ATF through the cooler fin stack, and onto the in radiator tank heat exchanger...and you sort of think of it as a 'thermal conditioner' of sorts...ie; if you did cool your ATF down to 65C, the coolant will add a little heat, otherwise it works as intended... ...the 'hot' ATF coming from the front bango bolt, is instantiated from the TC when in use, so all/any flash heated oil, flows to the fluid-to-air cooler first, and because of the greater heat differential, you can get rid of this heat fast. Just how big (BTU/h) this cooler needs to be to effectively dissipate this TC flash heat, is the charm...too many variables to discuss here, but I just wanted to point out the nitty-gritty of automatic trans fluid coolers ~ they're a different beastie to what most ppl think of when considering an 'oil cooler'... /3.5cents   
×
×
  • Create New...