Jump to content
SAU Community

Recommended Posts

Needed a roof rack in a hurry.

Used some 25mm OD pipe, Cyclone scaffold tees, 25mm ID clear plastic tube, black paint and duct tape.

The horizontal section of the tees needed flattening a bit to more nearly be the shape of the rails.Pipe was cut 920 for back, and 945 front. They are different, and the front was cut a bit short so it can be moved back to the centre of the rails. Metal parts were sprayed matt black and the tube was slit along its length to make it easier. Duct tape was wrapped around the hose, and also around rails where tees were clamped.

After using I had to move the front cross piece back to the centre because of wind noise.

Total cost if buying all the bits, about $20.

0000023gj9.jpg

0000024lt7.jpg

Edited by 66yostagea
Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/
Share on other sites

just for interest's sake,toyota rav 4 roof racks are a straight bolt on for stageas. I run a pair of ex-warranty rav racks on my S2.

new from toyota they're about $280 a pair.

Justin...

I used my Subaru Racks, $350. Big difference $20. They do the same thing. lol

Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2338641
Share on other sites

I used my Subaru Racks, $350. Big difference $20. They do the same thing. lol

it IS a big difference,providing you actually pay it. I got my rav racks for free,out of the warranty bin at clean up time. I have a heap of roof rack parts at home,including some rx330 aero racks. will try those on at some point as well. if they work,someone can have my rav racks if they need a set.

Justin...

Edited by fergo308
Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2339114
Share on other sites

Nice work there Hugh! So when are you going to start making them enmasse and sell them on SAu in a group buy for $50? ;)

That is what is the rage lately, I am still trying to find out what I can setup a Group Buy for :cheers:

And damn, you really dont have any sunroofs, bummer :ban:

Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2339141
Share on other sites

i can imagine what that will do for your highway fuel consumption. i think i'll be going for a more aerodynamically designed one.

Even with my ex Subaru and Skyline racks I always had to move them back a bit from the front.

As I've said elsewhere, " if you can't afford the petrol,you can't afford a Stagea".

Anyway, racks are not usually an everyday use. The bars take 5 mins to remove. The whole idea was to make something pronto.

As far as agroup buy, The only tools needed are a hacksaw (or angle grinder) to cut the pipe, a 10mm open ender and a Stanley knife, so it is very easy to make. Not really worth the postage.

Link to comment
https://www.sau.com.au/forums/topic/126638-roof-rack/#findComment-2339593
Share on other sites

  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...