Jump to content
SAU Community

Recommended Posts

well last night i went to leave for work and got about 20 metres down the road and couldn't see out my rear view mirror from all the WHITE smoke so naturally i quickly pulled a u-turn and put the car in the garage and took the girlie's car to work as i was running late as it was!

Now i'd just put a new catch can on that i'd made and i just presume i didn't vent it properly (was trying to make it legal) which caused this mess!

Now this morning i put my old catch can back on which is vented with a filter and a few small 1/8 holes! I took it for a drive and it was still smoking but not quite as bad! I'm hoping this is just oil that was still in the exhaust etc burning off??? i pulled back into the garage and there was oily smoke coming from the engine bay (mainly around the turbo, can see slight oil marks/stains where the dump pipe meets the exhaust housing) and exhaust!

Basically have i stuffed something (can't see how?) or do i just need to vent my new catch can and wait for the oil to get out the system? I was reading somewhere that its illegal to have a 'venting' catch can but if you don't vent it properly does this problem i'm having happen or have i made it or hooked it up wrong?

Cheers in advance!

Link to comment
https://www.sau.com.au/forums/topic/127654-urgent-help-please/
Share on other sites

Have done this a few times as well and it seems to clear up fairly quickly and I dont think it will be damaged. :(

Probably idle it off in the driveway as some mongrel will see the smoke if your on the road and dob you in to EPA.

Your breather should by rights vent back into the airbox intake.

I had the same problem, the catch can has a breather in the system... should work ok, are you still getting oil smoke? You may of damaged the oil seal on the turbo? Go have a look at your intercooler, you should find oil deposits in there! Clean it out with metho/kero (ie drain it n empty until it runs clean, DONT tip the cooler upside down as the oil will run through it lol) and clean the pipes out then go for a hard drive to burn any oil sitting in the zorst and have another look to see if that helps, personally im still abit stuck with it all but im tryin the cooler cleaning next week.

I had the same problem, the catch can has a breather in the system... should work ok, are you still getting oil smoke? You may of damaged the oil seal on the turbo? Go have a look at your intercooler, you should find oil deposits in there! Clean it out with metho/kero (ie drain it n empty until it runs clean, DONT tip the cooler upside down as the oil will run through it lol) and clean the pipes out then go for a hard drive to burn any oil sitting in the zorst and have another look to see if that helps, personally im still abit stuck with it all but im tryin the cooler cleaning next week.

i hope its not the turbo cause i've been through that with my old turbo and my new 35/40 is only 2000kms old so it better not be that!, i'm 99% certain its the catch can because it only happened when i installed the new catch can!

The catch can needs to vent to atmo or somewhere...crankcase pressure will build up and bad breath will come out somewhere else. Std breather goes back into intake pipe so instead just put a little filter off a hose tail on your catch can somewhere and let it breath off that.

The catch can needs to vent to atmo or somewhere...crankcase pressure will build up and bad breath will come out somewhere else. Std breather goes back into intake pipe so instead just put a little filter off a hose tail on your catch can somewhere and let it breath off that.

this is what i thought but i heard that venting into the atmosphere is illegal with catch cans? I have my old catch can back on (the one in the pic which vents via a filter!) It seems to be fine, just getting all the oil out the system now is the pain staking part. Mind you it is still blowing a bit of smoke but nowhere near as much!

Edited by mr_rbman

just took it for a quick hard drive and it only smokes a tiny bit driving normally but when it hits boost the smoke is much worse! To me that sounds like the turbo but considering its new and i changed the catch can and all this happened i'm still lenaing towards the catch can being the source of the problem???????????????????

just took the cooler off and there's a bit of oil in that which is probably causing the white smoke when the engine hits boost! Currently cleaning it now and will hopefully get it back on tonight fingers crossed!

Latest ZOOM has a great little article regarding crank case pressure and the ins and outs of oil catch cans and oil breather cans.

There was also a thread here recently where someone had a similar issue after putting on a new can and using wrong size hoses.

I think that thread started off saying “hi flow turbo blown” or something (because of the white smoke)

Even after fixing, there was a bit of smoke as the extra pressure had pushed oil past the turbo seals and so forth and was burning in the exhaust for a bit.

Hope that is all you have done and that nothing is broke.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
    • the Tomei LSD fluid with lsd kit. frustrated that it was shaking the car to crap and affecting everything else negatively, I pulled the diff last night, and removed the lsd carrier, could not find anything wrong, however it seem to be 100 locked up acceleration, and deacceleration, wondering if they sent me a 2 way not a 1.5??  either way I installed the stock open carrier back in place. test drove everything smooth as butter again. no shake, shutter, random, what felt like clutch slip and grab or drive shaft play, etc. something differently wrong in side the lsd. I might bother taking it apart (if possible) to figure out what's going on inside this carrier, as bought too long ago to return.  only draw back is its back to a one wheel wonder.
×
×
  • Create New...