Jump to content
SAU Community

Recommended Posts

well last night i went to leave for work and got about 20 metres down the road and couldn't see out my rear view mirror from all the WHITE smoke so naturally i quickly pulled a u-turn and put the car in the garage and took the girlie's car to work as i was running late as it was!

Now i'd just put a new catch can on that i'd made and i just presume i didn't vent it properly (was trying to make it legal) which caused this mess!

Now this morning i put my old catch can back on which is vented with a filter and a few small 1/8 holes! I took it for a drive and it was still smoking but not quite as bad! I'm hoping this is just oil that was still in the exhaust etc burning off??? i pulled back into the garage and there was oily smoke coming from the engine bay (mainly around the turbo, can see slight oil marks/stains where the dump pipe meets the exhaust housing) and exhaust!

Basically have i stuffed something (can't see how?) or do i just need to vent my new catch can and wait for the oil to get out the system? I was reading somewhere that its illegal to have a 'venting' catch can but if you don't vent it properly does this problem i'm having happen or have i made it or hooked it up wrong?

Cheers in advance!

Link to comment
https://www.sau.com.au/forums/topic/127654-urgent-help-please/
Share on other sites

Have done this a few times as well and it seems to clear up fairly quickly and I dont think it will be damaged. :(

Probably idle it off in the driveway as some mongrel will see the smoke if your on the road and dob you in to EPA.

Your breather should by rights vent back into the airbox intake.

I had the same problem, the catch can has a breather in the system... should work ok, are you still getting oil smoke? You may of damaged the oil seal on the turbo? Go have a look at your intercooler, you should find oil deposits in there! Clean it out with metho/kero (ie drain it n empty until it runs clean, DONT tip the cooler upside down as the oil will run through it lol) and clean the pipes out then go for a hard drive to burn any oil sitting in the zorst and have another look to see if that helps, personally im still abit stuck with it all but im tryin the cooler cleaning next week.

I had the same problem, the catch can has a breather in the system... should work ok, are you still getting oil smoke? You may of damaged the oil seal on the turbo? Go have a look at your intercooler, you should find oil deposits in there! Clean it out with metho/kero (ie drain it n empty until it runs clean, DONT tip the cooler upside down as the oil will run through it lol) and clean the pipes out then go for a hard drive to burn any oil sitting in the zorst and have another look to see if that helps, personally im still abit stuck with it all but im tryin the cooler cleaning next week.

i hope its not the turbo cause i've been through that with my old turbo and my new 35/40 is only 2000kms old so it better not be that!, i'm 99% certain its the catch can because it only happened when i installed the new catch can!

The catch can needs to vent to atmo or somewhere...crankcase pressure will build up and bad breath will come out somewhere else. Std breather goes back into intake pipe so instead just put a little filter off a hose tail on your catch can somewhere and let it breath off that.

The catch can needs to vent to atmo or somewhere...crankcase pressure will build up and bad breath will come out somewhere else. Std breather goes back into intake pipe so instead just put a little filter off a hose tail on your catch can somewhere and let it breath off that.

this is what i thought but i heard that venting into the atmosphere is illegal with catch cans? I have my old catch can back on (the one in the pic which vents via a filter!) It seems to be fine, just getting all the oil out the system now is the pain staking part. Mind you it is still blowing a bit of smoke but nowhere near as much!

Edited by mr_rbman

just took it for a quick hard drive and it only smokes a tiny bit driving normally but when it hits boost the smoke is much worse! To me that sounds like the turbo but considering its new and i changed the catch can and all this happened i'm still lenaing towards the catch can being the source of the problem???????????????????

just took the cooler off and there's a bit of oil in that which is probably causing the white smoke when the engine hits boost! Currently cleaning it now and will hopefully get it back on tonight fingers crossed!

Latest ZOOM has a great little article regarding crank case pressure and the ins and outs of oil catch cans and oil breather cans.

There was also a thread here recently where someone had a similar issue after putting on a new can and using wrong size hoses.

I think that thread started off saying “hi flow turbo blown” or something (because of the white smoke)

Even after fixing, there was a bit of smoke as the extra pressure had pushed oil past the turbo seals and so forth and was burning in the exhaust for a bit.

Hope that is all you have done and that nothing is broke.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...