Jump to content
SAU Community

Recommended Posts

from my knowledge of the rule its ok as the pods would be considered 1 intake mod. if you were to change the intercooler that would count as two intake modifications. best to ask vic roads as a lot of their rules are full of grey areas and exceptions

when i spoke to the EPA last about aftermarket front mounts, they said as long as you can prove it is within stock dimesions then its fine. But i couldnt be assed taking off the front bar to measure up the cooler and just used a stock air box instead!

Im sure this has been asked before, but would i get away with a enclosed POD? Legally? Its still a modification but.. not off the shelf, and its roadworthy so.. any ideas?

the pod doesnt have to be enclosed as far as i'm aware (although its useless if exposed to the engine bay anyway)....

As long as its secured to the car, and is the only intake mod, its legal

Someone from EPA mentioned if you have a Pod Filter it has to be the Dry kind not the Oil Soaked ones. Anyone confirm this?

The Reason why I ask is because everytime I ring up I get a different response.

Edited by beefy

what if you have a pod in and enclosed box that you cannot see, and a cooler, what can be done ?

When i called the EPA regarding this i was told only an exposed pod OR a cooler. Unless the car comes with a factory intercooler then you can have a pod as well.

Someone from EPA mentioned if you have a Pod Filter it has to be the Dry kind not the Oil Soaked ones. Anyone confirm this?

The Reason why I ask is because everytime I ring up I get a different response.

Oil Soaked pods are illegal, the dry kind are fine.

what if you have a pod in and enclosed box that you cannot see, and a cooler, what can be done ?

When i called the EPA regarding this i was told only an exposed pod OR a cooler. Unless the car comes with a factory intercooler then you can have a pod as well.

Having a pod, whether it be enclosed or not and a Intercooler thats not stock or is relocated is illegal.

A pod with a stock cooler is legal.

A FMIC and stock airbox is legal.

You could get alway with an enclosed pod if the box looked factory, but its still illegal.

Cheers

Edited by stealth01
  • 3 weeks later...

If that's the case, I need some help. I have actually 'misplaced' my stock air box in my garage (it happens). Can't find it anywhere now. And I have ordered a new FMIC recently. Since I still want my mods to be legal, I want to replace my pod with a stock air box again. Anyone out there willing to sell me their stock air box. I have a R32 GTS-T and I live in the outer east (Knox area).

EPA Mod Rules Extract February 2006

© Intercoolers that are larger than standard or have a different mounting location or are added where none were originally fitted, are permitted only if no other changes to the intake system have been made. In other words, you may have a pod filter or modified/added intercooler, but not both.

Any sensors integral to the original intercooler or intake system must be retrofitted and be in the correct location. Note: aftermarket turbocharging kits that include intercoolers that have been type tested (ADR certified) for the model vehicle are permitted. Documentary proof must be retained to substantiate this.

(b) Dry element pod type air cleaners are permitted on EFI vehicles. Oiled, oil-soaked or fluid-treated elements are not permitted. Any sensors integral to the original system must be retrofitted to the same approximate location.
Variable turbocharger boost valves (‘boost controllers’) or other means of altering boost levels are not permitted unless part of an original manufacturer’s fitment. ‘Blow off’ (‘pop off’) valves must be plumbed back into the system. Atmospheric venting is not permitted. External wastegates are not permitted.
Non-original electronic chips or computers, whether fitted as a direct replacement or in a ‘piggy-back’ configuration, are not permitted to be used in an engine management system unless it can be demonstrated that their installation and use allows the vehicle to meet the appropriate ADR. They must also be sealed or otherwise constructed so as not to be reprogrammable.

So who here can say they do not breah any of the above rules?

With my new setup, me.

Either way, its not a question of who can pass or not.

The rules are there, they are readily accessible.

So next thread about "can i have a pod" gets locked :(

hehehe...i wold have thought most ppl would have aftermarket ECUs and boost controllers... Pods and ICs are visible and hence gain the majority of the attention. Just don't drive like a hoon or be on P plates...The insurance companies don't seem to care much, having made a massive claim with most of these known on their books they still payed out no quetsions asked. I would have thought they would go to town on this stuff, maybe they do sometimes and I was just lucky.

hehehe...i wold have thought most ppl would have aftermarket ECUs and boost controllers... Pods and ICs are visible and hence gain the majority of the attention. Just don't drive like a hoon or be on P plates...The insurance companies don't seem to care much, having made a massive claim with most of these known on their books they still payed out no quetsions asked. I would have thought they would go to town on this stuff, maybe they do sometimes and I was just lucky.

Has anyone experience problems with their insurance companies from their mods?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...