Jump to content
SAU Community

Recommended Posts

HI! everyone i got an R33 GTSt wrecking at the moment ,i havnt made up a list yet or price will do that on tuesday afternoon.I will take any inqurie if anyone are chasing for R33 GTST parts till the list come up .the car been hit on the left front bonnet,guard and LH door are no good.that all for now list be up on tuesday afternoon.

pm me or email me on [email protected] or call on 0415642296.din.

post-21589-1154426805.jpg

post-21589-1154426979.jpg

post-21589-1154427012.jpg

post-21589-1154427031.jpg

post-21589-1154427051.jpg

post-21589-1154427086.jpg

post-21589-1154427108.jpg

post-21589-1154427169.jpg

post-21589-1154427190.jpg

post-21589-1154427220.jpg

post-21589-1154427346.jpg

post-21589-1154427425.jpg

post-21589-1154427573.jpg

post-21589-1154427599.jpg

post-21589-1154427668.jpg

post-21589-1154427752.jpg

post-21589-1154427773.jpg

post-21589-1154427853.jpg

post-21589-1154427884.jpg

Edited by dinzlr
Link to comment
https://www.sau.com.au/forums/topic/128339-wrecking-r33-gtst-whole-cars/
Share on other sites

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

hmm dude would you have the plastic covering bit on the side of the driver seat??

You know that black looking thing, that covers the reclineably push lever thingy??

You know what im talking about?? Its just one bolt..

20bucks??

Edited by siddr20

Hey mate,

Are you willing to sell parts off the engine, or are you planning to sell it whole?

As I'm after the "U" shaped rubber hose that goes between the two vents on the rocker covers, and also the knock sensor loom.

Cheers, Ryan

hey dude you would have it.. I can see bit of it from pic 2..

look at the driver seat. Look at the bacl thing under it sorta..

You know when you put the lever up so the seat reclines..

Hmm i dont have camera to take a pic of mine..

look at pic 2, you can see it..

Edit: This pic: http://www.skylinesaustralia.com/forums/in...st&id=49430

Edit 2: How much for that gtr wing?? Cheers

Edited by siddr20

Do you have the plastic bit under the drivers side? Under the steering colum, the plastic that covers the fuses and the wiring under it etc.. $10?

Driver side floor mat?

Power steering pump? (Just want a rough est on price)

And if you are wreaking engine (though I doubt it) CAS Whole unit.

Cheers

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...