Jump to content
SAU Community

Recommended Posts

hi i just installed a auto meter air fuel ratio gauge straight from ecu wire pin out 29...anyway its very eratic i wound the boost up tp 10 and i get a missfire under boost and a/f gauge says car is leaning out like even at idle it even drops completetly off the gauge on the l;ean side..gauge faulty? its hardly ever in green basically stock r33 gtst s1 fmic exhaust..pod....

eratic gauge

what u think gauge rooted wrong wiring?

missfie

boost ? pugs gapped wrong?

plugs farked? coil packs

its not r&r :miner:

vacuum leak i dunno its driving me crazy...cars fine on standard boost dosent miss a beat under 10pound boost missfire quite a bit

Edited by SS#eater

the air fuel ratio guage is erratic as its read of the stock slow and narrow sensor. its not accurate enough to give any useful data on an af guage. if you had a wideband 02 sensor it would be spot on and accurate. you are best off either ignoring the output from the guage, change to a wideband 02 sensor or sell the guage and move on. the guage and the stock 02 sensor will never be accurate.

the misfiring could be the r&r protection being activated in the stock ecu. try at 9psi and see if happens at that pressure

the air fuel ratio guage is erratic as its read of the stock slow and narrow sensor. its not accurate enough to give any useful data on an af guage. if you had a wideband 02 sensor it would be spot on and accurate. you are best off either ignoring the output from the guage, change to a wideband 02 sensor or sell the guage and move on. the guage and the stock 02 sensor will never be accurate.

the misfiring could be the r&r protection being activated in the stock ecu. try at 9psi and see if happens at that pressure

at 9 it is fine not a problem....i am quite happy at 9psi

paulr33 or anyone can u recommend a wideband 02 sensor suitable 4 my needs maybe part number...cost any info plz thanks 4 helping :miner:

yeah they arent cheap and are really only useful when you can tune the fuel injection. its kinda pointless to have one in the car full time without being able to change anything. unless you have different ecu ?

like the above guys have suggested the autometer AFR guages used with standard O2 sensor are a waste of time. I'ts about as good at telling you your AFR as your stereo is.

haha

yeah i noticed that...i have a power fc comming..wanted the a/f to be sure everything went right when pfc goes in :)

thanks anyway...i will put the a/f gauge on hold...spend my little amount of money on better things...

cheers

  • 2 weeks later...
but the guage looks cool rite?

Hay guys maybe you's can help me out as well my a/f gauge doesnt not bounce back and forth between lean and rich it just sits on stoich with about 4 lights lit up when you accelerate it might move 2 bars towards rich, but it has never bounced back and forth (like i have heard and have read its supposed to) is somthing wrong with gauge or is it normal for a 1.5 series skyline,also i have wired it up in accordance with autometers installation guide.thanks in advance.Also im not using standard computer anymore im using power fc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...