Jump to content
SAU Community

Recommended Posts

the gtr twins are located after the front mount but before the plenum.

im not sure how they are attached to the fmic piping. they are near the water bottle washer. i dont think it would be a direct swap and would need an adapter plate to mate it up. what problem did u have with the stock one?

if that fails, you should have a look at the GFB Hybrid bov. it's able to be fully plumbed back, and has quite a bit of spring adjustment. Contact Brett Turner at Go Fast Bits. He'll sort you out.

http://www.gofastbits.com.au/

Edited by Munkyb0y
A stock gtr bov will bolt on...i've got one on my car...only thing is u need a larger diameter plumback hose as the gtr one is considerably larger...

any idea what diameter? an what sort of length hose am I in need of? any pics of your set-up (how you've changed the hose)?

glad to hear it'll just bolt on.

everyone keeps saying turbo surge......the flutter is only when changing gear...ie not on boost...ie when the BOV opens an due to not strong enough spring in there its bouncing.....fastly open/closing.....fluttering.....so how can this be a turbo problem?

  • 2 weeks later...

well yes, it bolts straight up, used the top radiator hose from Telstar TX5 (cut a small straight section from it) to plumback to standard pipe (as the GTR outlet is a bigger diameter). using the old pipe I cut about a 3cm lenght of it off an put it in the other end of the telstar rad pipe as a reducer onto the stock plumback steel pipe.

but I still have the flutter :), an now if my timing of getting my foot off the accelerator when clutch goes in isnt perfect, I get a touch of VL turbo full sik dose pipe noise. strange...I thought the GTR bov would be better than the standard item...its pretty much the same.

luckily it only cost me $40 or id be pretty un-impressed, but now I guess i do get to add "GTR BOV" to the modifcation list of my car....lol

they have stiffer springs, the outlet pipe is bigger diameter an so is the diameter of the BOV inlet hole (part that bolts to pipe)

an if you sit them side by side...they dont look the same (RB20/25 BOV's made by Mitsubishi, GTR BOV's Made by nissan)

but I still have the flutter :), an now if my timing of getting my foot off the accelerator when clutch goes in isnt perfect, I get a touch of VL turbo full sik dose pipe noise. strange...I thought the GTR bov would be better than the standard item...its pretty much the same.

weird man.

I never once had an issue with my single GTR BOV.

It let off perfectly every single time... But then, Race Pace was where it was fitted... highly likely that was some sneaky change/mod to it :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...