Jump to content
SAU Community

Recommended Posts

hi peoples...

I've just finished reading an article in the latest "ZOOM" magazine about the datsun 1600 SR20det on gas...

From reading the article it seemed to me there were some serious advantages for a straight gas system in a turbocharged application.

Some of the advantages of using straigh gas (according to the article) are;

*better fuel economy "flat out, insterstate travelling 600km to a 60 litre tank"

*The higher octane level in the gas allowed 35 degrees of timing

*High RON rating which is perfect for high boost engines (with no detenation)

*No need for upgrading injectors, fuel pump, pressure regulators...

He's spun up 228kw at the wheels..

To me this seems like the perfect way to go .. but i'm hesitant as i havn't seen many high performance cars using gas.

Is there any disadvantages ?

Any input would be appreciated. As i would consider it for my rb20det.

Travis

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/
Share on other sites

Probably the biggest disadvantage in a Skyline is you will lose most of your boot space. The tank and equipment also adds a fair bit of weight to the car so with the same power your car will be a little bit slower. But I have seen several turbo drag cars running on gas, I think the most famous is the 11 second street-driven XE Falcon. Not too sure about this "flat out, insterstate travelling 600km to a 60 litre tank" though, I can already do that with my R33.

Aside from the initial cost and extra weight I can't think of too many drawbacks. I think it's not as popular with the weekend driven cars because it takes a lot longer to recoup that initial outlay due to the relatively low amount of km done.

Oh another advantage to it is you never have to worry about getting defected for emissions :D

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-244091
Share on other sites

Also, all gas systems use a carby setup, meaning you'll never get perfect mixtures at mid throttle, midload situations.

All the fuel maps on your CPU will not be required...

To have a properly setup hipo gas system you would most likely require some changes to your engine, as per the hotter combstion point above and also I think LPG lacks some of the lubrication qualities that petrol has...

And the weight/space dissadvantage, but you do get very cheap 100 RON+ fuel.

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-244349
Share on other sites

I was always under the impression that LPG had a low octane rating. In the 80s somewhere. One of the guys I work with has a LPG converted Falcon and he says he loses a fair bit of power when he switches over. Also, the stock LPG AU Falcon had less power than the petrol one. Can anyone explain this?

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-244398
Share on other sites

It's most likely just in the tuning - think about it, the majority of people that convert to LPG are only really interested in the cost savings - not potential power upgrade.

Also just because it's higher octane doesn't automatically mean more power, if you put a higher octance petrol in your car more than likely you won't pick up much, if any extra power. All a higher octane number means is its more resistant to detonating, meaning you can run more aggressive ignition timing and/or more boost, and in turn getting more power.

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-244426
Share on other sites

I have heard that you will not get any performance gains if your running a dual fuel system (switchable from petrol to gas) In this method the car is tuned to the two types of fuel therefore compromising performance on either switch.

Running a straight gas setup your car is tuned primarily to gas..

This is only what i've heard..

Travis

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-244460
Share on other sites

meteor - I'd say it would have been tuned - I mean a car with optimal A/F ratios is usually more economical. He did it for cost savings, so economy was important.

R31 - Fair enough, If it wasn't tuned for both then I can understand that, but that doesn't explain why the stock AU Falcon on gas (from the factory) makes less power than the petrol model. Surely they would tune it?

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-244475
Share on other sites

There are two main reasons why factory cars usually make less fuel on gas. Firstly, they are usually dual fuel which means they can't advance the timing as much, in order to enable it to be run on regular unleaded when needed. The second is that LPG has less energy in it than normal petrol.

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-244491
Share on other sites

Originally posted by MIC33R

meteor -  I'd say it would have been tuned - I mean a car with optimal A/F ratios is usually more economical. He did it for cost savings, so economy was important.

A/F ratios are one thing, advancing the timing is another. Also it's possible that the most ecomonical A/F ratios do not provide the best power... But at the end of the day, I doubt it would make that much difference on an NA falcon.

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-244529
Share on other sites

i don't even know whether straight LPG would be possible without some serious fiddling with the inside and outside of the engine??

Isn't the whole idea of a turbo engine you compress the air and fuel a lot more to get better power out of less (cylinder) space ? Does that translate for gas even at all?

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-245461
Share on other sites

Running straight gas could be advantagous as you could lose the the weight of a fuel tank injectors ect, and mount the bottle in the fuel tanks place or run 2 skinny bottles for a 32 thus keeping boot space, the gas jet would need to be mounted before the factory throttle body but after the ic.

boost would help compress the gas more compared to a high pressure fule system with injectors and the gas is already under pressure and compressed in the bottle.

The luberication issues with gas was only with cars running on the old super leaded type fuel wasnt it?

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-245853
Share on other sites

fatz.... 4k on a gas system??

I got quoted $1700 drive in drive out..

so then i gots $2300 to spend on a massive turbo..

then keep up with me :)

damqik GTS-T .. u sound like you know a lot about his issue.. do you know anyone who has done the conversion on an RB series engine? in your personal opinion would you say its worthwhile?

Trav

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-245968
Share on other sites

RED17 a vl (rb30) dosn't have a blow off valve to protect the turbo from backfires a rb20det - rb25det & rb26dett dose backfire's wouldnt be an issue. A backfire on gas would be caused from incorrect tuneing or when changeing from one fuel to the other (duelfuel setup).

R31_GTSX I used to work for a shop (in Nundah Qld) that did lpg conversons.

I have only seen the rb30 motor on gas and some vg30's none of which had any issue's.

Damqik

Link to comment
https://www.sau.com.au/forums/topic/12950-rb20det-on-gas/#findComment-246975
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Guys since i bought r33 gts25t coupe 1994 automatic a/t(manual swap 350z gearbox)  all i got is problems, always problems. Lets start with that when i turn key into ignition(ON) fuel pump doesnt always works. Sometimes i have to turn key twice Off/on/off/on until it primes. Its new, dw300 - 340lph. My gearbox broke so i did gearbox swap, install different intake manifold, injectors and i take pipes. Car was sitting in garage for more than half a year. I did assembly all not that long ago and when i turn ignition cant hear prime. All of sudden it stopped working. Theres many videos on YouTube how to make relay mod on r33 straight from battery so i did and it doesnt work! 😰 30 - battery positive  87 - positive from fuel pump to relay 85, 86 - one of two wires from original fuel pump wires(light blue, grey) and it didn’t work. so I check on ignition and took original BLUE relays wires from trunk, next to fuses. (I believe it’s IGN+ and ECU pin 18. it didn’t work…  tried connecting (IGN+ from og relay) and (ECU 104 from 1of4 FPCM wires) to my new relay 85/86 and it didn’t work.  I unplug FPCM. Didn’t work. im thinking what’s wrong   fuel pump is working, if I leave IGN+ on 85 and 86 straight to ground it works but it’s just nonstop. Since it getting constant 12v after key in ON. light blue wire gives me 6-8v.  so how this should be connected? What causing ECU not giving — on pin? Or I did sth wrong and that’s why it doesn’t work? I need negative signal on ECU that control fuel pump. What this should be?
    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
×
×
  • Create New...