Jump to content
SAU Community

Recommended Posts

1999 34 GTR Vspec

-49000k's

-19 X 9.5 gold rays engineering wheels

-Genuine volk centre caps

-275 yokahama tyres all round

-Calsonic 3 1/2 stainless cat back exhaust

-Stainless front pipe

-etch tinted glass...dark and legal

-Alpine touch screen all in one unit ($3000)

-K & N panel filter

-Kicker 6.5" splits in front

-Kicker 6.5" coaxials in rear.

-Nismo eyelids

-Nismo blinkers

-Nismo Dash

-Nismo Fuel Pump

-KYB rear suspension

-Brandnew O2 sensors

- serviced with full synthetic oils and platinum plugs.

This car runs like new, 0.9 bar standard, Ball bearing turbo's, 6 speed Getrag gearbox.

[email protected]

Concider offers of around $79 000

post-412-1155180880.jpg

post-412-1155180893.jpg

post-412-1155180911.jpg

i must say your car is beautiful, awesome rims too (and damned expensive). when was this car imported to aus? and what auction grade was it just out of curiosity? gl with the sale

Edited by VB-

This car was imported 4 years ago at huge expense at grade 4.5 with 10000 k's. Fully serviced by Metro Nissan Gold Coast.

i must say your car is beautiful, awesome rims too (and damned expensive). when was this car imported to aus? and what auction grade was it just out of curiosity? gl with the sale

Rick will you part with the wheels seperatly or did you already sell your stockies? Can't hurt to ask :D Nice car mate as I've said before if I didn't already have one i'd be knocking on your door.

Gee the wheels are popular...everyone asks that. I have sold the standardies. My new house is in full swing now and the bank account doesn't like it...

Rick will you part with the wheels seperatly or did you already sell your stockies? Can't hurt to ask :) Nice car mate as I've said before if I didn't already have one i'd be knocking on your door.
  • 4 weeks later...
  • 2 weeks later...

I'll try and get some new pics with the better ride height.

Still has standard clutch, I might try to get a new one and lay down a 1/4 just to see what its capable of.

I am open to serious offers in the meantime though...my house is nearly built

  • 2 weeks later...
  • 3 weeks later...
  • 3 weeks later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...