Jump to content
SAU Community

Recommended Posts

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

' date='14 Oct 2006, 12:17 AM' post='2581709']

still got:

R33 GTST Series 2 Dash surround including aircon vents (missing power arial switch) $150

(also need then ones that go in the door, and just behide the front winscreen for the aircon)

will u ship to perth?

+$25 in box and protected for shipping

How about the underhood snorkel? You know the little black thing that goes from under the hood into the airbox.

-Sayajin

no sorry

do you by any chance have the internal fuse cover or the engine bay relay cover?

no sorry

:w00t:

I'm after the little pocket that sits undernearth the head unit, have you got it separate or is it part of the centre console? and price?

Thanks

are you talking about a DIN pocket? These can be had from Nissan for about $15 - $20.

Got one in my car, because I upgraded to a Single slot (din) head unit.

do you have a the Front grille? Is it a series 2 if you do?

If so, sold to me.

Thanks

do you still have the series 2 front indicator and fog light assemblies? Would b interested.

This was a a front impact crash

There is nothing available that is not in this thread.

:(

Hey i only need a left hand rear tail light if you still have it will u sell it individually. For my 94 r33gtst

phone: 0406075274

Pm sent :laugh:

  • 2 weeks later...
Do you have the high pressure hicas power steering hose or the stock turbo to intercooler piping?

Yes i have all of that :P

Where are you located?

Your pm box is full mate.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...