Jump to content
SAU Community

Recommended Posts

  • Replies 245
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Glad to hear you just receive it. For those in first batch who haven't received it, please allow till Wednesday. Contact me if not yet receive by then and I'll follow up with Scott at the head office here in Keysborough.

The rotors (as well as most new automotive parts) are always covered in a coat of oil, the reason to this is to prevent rust over long period of storage or exposure to moisture during transport.

You don't need to get it oil free before installation, but give it a good wipe around the rotors with a piece or rag clothing. If you asking a mech to do it, they'll know what to do.

If you're not gonna install it soon, just leave that coat of oil on your rotors until you're ready to install it.

just got mine great work rianto. didnt realise how much of a discount we got. if anyone is waiting like i was. there doing deliveries out my way s.e melb.

thanks again.

let me know how you guys go with them. can hear mine rubbing against the pads. not sure if they do that will beding in or not? still bit of oil on them too maybe thats a factor? havent put new pads on yet either running the pads i had with the old rotors. piece of paper in the box said to replace pads but havent as yet.

jasont82 - I am pretty sure and the dba instruction sheet said that you are supposed to use a non oil base cleaner and clean the oil off the sides of the rotors that touch the pads before you fit them. I couldn't imagine the rdas would be any different?? Have you done this?? If not I would check and clean them before fitting the new pads....

rs73 - received my rotors today. Thanks for organising the group buy. Cheers

let me know how you guys go with them. can hear mine rubbing against the pads. not sure if they do that will beding in or not? still bit of oil on them too maybe thats a factor? havent put new pads on yet either running the pads i had with the old rotors. piece of paper in the box said to replace pads but havent as yet.
Edited by operationsideways

I was told by my mechanic that the general rule is you should always replace pad when you replaced the rotors, rotors are too expensive to get scored by old pads that has poor surface, I didn't replaced mine but at that time of replacement on the front, the front pads were less than a few thousands km and there's hardly any grooves on the old rotors, so the pads were ok. I'm not sure if sanding or machining your old pad to obtain a flat surface will work just as good as new pad or not...

post-25470-1158564325.jpgpost-25470-1158564386.jpgpost-25470-1158564481.jpgvery easy to install. look great thanks again. :laugh:

Can you change do mine aswell? :laugh::D;):laugh::laugh:

Thanks received mine today,,....great group buy to the organisers :):)

Evening update:

I've decided to submit the 2nd batch of group buy tomorrow as there's another 3 transfer coming through today and perhaps 1 more tomorrow. So there will be 10 people in the 2nd batch. Looking at how fast some of you who were in the 1st batch, I'm sure that the 2nd batch will be delivered before Friday...

All 15 people from the 1st batch have received their rotors...

Got mine today... delivered to my office. Damn they are heavy. Ended up carrying them from my office in the city, gone home by train and 15 mins walk from the station... nearly broke my arms in the process, but definitely worth it. Looks good.

Thanks heaps Rianto for organising this. You're a legend mate!

DD

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...