Jump to content
SAU Community

Recommended Posts

When driving my skyline (R32 RB20DET Manual), as soon as i reached

the 2100rpm mark on acceleration, it sort of feels like its holding back but it jerks

forward like it doesn't know what it wants to do. When i put my foot down to

accelerate its ok, once past 2100rpm, not a problem.

Link to comment
https://www.sau.com.au/forums/topic/130905-car-is-hesitating-at-2100rpm/
Share on other sites

are you still running the standard fuel pump? if so sounds like it is on its way out. from what i can read i beleve u have a bit of fuel surge as the fuel pump can no longer pump fuel fast enough, giving u that hesitation.

ive done plugs, last owner changed coil packs and now has the current 1s taped up and mine does the hesitating thing..... ive had it for 2 years, still does it, maybe the fuel pump..... but if it was on its way out, should of gone by now

I've now got a GTR pump in mine and that hasn't fixed the problem.

This came up a few times , so do a search on what it could be.

I think AFM , Injectors followed by OXY Sensors was the discussion

on those topics.

sounds like an AFM problem! car sort of bunny hops like its got no fuel then goes again... clean your AFM with carby cleaner. if that dont work try the AFM soldering there a DIYS here some were. or buy another 1. i just brought a used 1 and fixed my problem.

hope this helps

Its a R32 Skyline, RB20DET.

I did clean my AFM with carby cleaner and did the re-solder on it.

I think i might clean it out with the carby clearner again.

I'm running coilpacks, havn't got leads.

Coil pack normally has troubles at high revs.Put injector cleaner into the fuel tank,

see if that might fix it.Changing the afm to find out it did not fix the problem would hurt your pocket.

Any one got a working AFM to lend to see if thats the problem?

Where abouts are you?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...