Jump to content
SAU Community

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

These look nice....more power and better response than a HKS GT2530....

As New TWIN APEXi AX53B60P21 680HP

http://www.jappartsspecialist.com/main.htm

Last I looked the GT2530's or Garrett GT2860R-5 Turbo's are rated at 700HP so how are you stating that.

:rolleyes:

So waiting for a reply on why the AFM's with the d-getro unit?

just from what the site says.....

I do like the the apexi design tho, would be more efficient than a HKS2530 given the same size.

"The AX turbo incorporates the AIRICK system. The AIRICK system incorporates a patented material in between the compressor housing and the compressor blade. The insertion of this material allows near 0 clearance between the blade and housing improving compressor efficiency by almost 5-6% all across the board. AIRICK also lowers compressor outlet temperatures under high load by 50-68 degrees F. This not only improves overall maximum output, but improves the boost response right before the intercept point of the turbine."

btw I run HKS 2530's =)

just from what the site says.....

I do like the the apexi design tho, would be more efficient than a HKS2530 given the same size.

"The AX turbo incorporates the AIRICK system. The AIRICK system incorporates a patented material in between the compressor housing and the compressor blade. The insertion of this material allows near 0 clearance between the blade and housing improving compressor efficiency by almost 5-6% all across the board. AIRICK also lowers compressor outlet temperatures under high load by 50-68 degrees F. This not only improves overall maximum output, but improves the boost response right before the intercept point of the turbine."

btw I run HKS 2530's =)

My warning was because of what was on a web site.

Don't listen to what they go on about in the turbo info section....

Look at the results and the mods. done in the performance threads...RB20,RB25,RB26.Upgrades

I have not seen may of these guys use this system HKS and Garrett seem to be the best choice.(both being the same turbo anyway)

Take care

The graph that is posted at the start of this topic by writeoff might be abit ancient too.

So looking at this would be incorrect to compare PSI of Turbo's.

IE. The old N1 turbo's are different from the new one's.

So waiting for a reply on why the AFM's with the d-getro unit?

The answer was ignorance. I knew nothing about D-Jetro Power FCs and hadn't done the research. I've read up on them since. Still haven't finalised what I need and therefore haven't ordered anything yet. Also waiting on results from leakdown test on engine before I order anything.

  • 4 weeks later...

Write off- I would avoid the D-jetro if you want the nicest car possible to drive. Djetro can make more power sometimes due to the absence of the AFM as a restriction but the djetro are much harder to tune and are drawing on a signal (MAP sensor) which is much less accurate than an AFM which makes for a car that doesn't drive quite as well. Unless your worried about every last kilowatt I would buy the AFM version and save yourself money on tuning and have a nicer car to drive.

very good list there. the only think I would change would be get nismo afm instead of Z32. 60mm afm is no big restriction considering the size of the intake piping is smaller than that anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...