Jump to content
SAU Community

Auto Salon Dyno Results

C-Red

By C-Red,
in Western Australia

 Share

Recommended Posts

C-Red Proficient

C-Red

Posted
Posted

Just thought I'd pop up a post to counter the inevitable sniping that is happening after our dyno results at Autosalon. The Dyno was run in Shootout Mode which means that all variables and adjustments are locked. 2 other cars (B REAL and Leslie's MX5) ran within 1 or 2% of what they made on SSTs dyno during the week. Bear in mind that figures touted by other tuners for their cars from previous "Salons" were not run in shootout mode and are subject to interpretation.

Jash

Link to comment
https://www.sau.com.au/forums/topic/13143-auto-salon-dyno-results/
Share on other sites
GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted

Jash,

I read all the post's in here and I don't think anyone has has a bad thing to say about the result. In fact all of us there were very impressed, even old Jaffey:D

We only have a go at the fact that you can only run 12sec with a 649rwhp car:p

I agree, the dyno results were very close to Steve's dyno and congrats on winning.

See'ya:burnout:

C-Red Proficient

C-Red

Posted
  • Author
Posted

Oh it may not be anyone in here, I just wanted to assure everyone in here that the results were legit, as per usual in Perth there's always someone reckoning we fudged the result.

Hey it was a poorly tuned 500rwhp car when it ran a 12 at 123. something mph :shake: . Will all be fixed with a Holly or some PPG gears and some Nittos.

Jash

GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted

Jash,

We know the car should be capable of much more at the plex, and we want to see a GTR take it to some of the V8 brigade.

WE will only bag you if you deserve it:D How much boost were you running, and is there anymore left in the engine at the moment?

See'ya:burnout:

C-Red Proficient

C-Red

Posted
  • Author
Posted

Quite a bit left in it based on how its going now. We just started using VP103 in it and we reckon that there is at least 500rwkw in it. We we're running 1.7 bar which is getting towards the meat of the efficiency for the 3037S. We'll see. Now I've just got to find a Holly sequential for the right money...

Jash

N I B Grand Master

N I B

Posted
Posted

The Dyno was even closer than that, BREAL and MX52NV made within 0.3%.

The runs were in shootout mode and for real.

So that is the highest figure in WA for a GTR and would be 734rwhp at Myaree and upto 800+ on the dynopack and dynojet

dynos. Good on ya Jash for outrite and Paul for the 4cyl crown.

Lets make Shootout mode STD for Shootouts to stop the fudged

figures that DO happen.

C-Red Proficient

C-Red

Posted
  • Author
Posted

Dude,

Ta Dude, nice to meet you all finally - met PVA too.

I'm a sucker for anything with Sparco on it. I also want one of those Superfun Happy baseball bats - I reckon it'd be hilarious to kneecap an intruder with one.

Jash

C-Red Proficient

C-Red

Posted
  • Author
Posted

Amen Hippie,

Shootout Mode is made for a reason and comes with every Dyno Dynamics dyno, if an operator says they havent got it then they are telling porkies. Also worth getting any power runs done in Shootout mode so you can compare with some degree of accuracy.

Jash

Denver Grand Master

Denver

Posted
Posted

Nice work jashy, be nice to see that thing at full boost and power finally, it sat in the shop waiting long enough for it to happen..

bring on the 1k mark and maybe perths first 9 second 4wd pass, might give the eastern states boys something to think about..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...