Jump to content
SAU Community

Recommended Posts

Hey there

i have an r33 gtst and my fuel gauge will not move of the full mark until i have done around the 300km's mark. Im wondering if this is a common problem for the r33 skylines cuz one of my mates 33 does the exact same thing but around the 250km's mark. does anyone have any idea of what i can do to fix this so that my gauge goes down consistently with my petrol usage?

cheers iLEC ;)

Link to comment
https://www.sau.com.au/forums/topic/131466-fuel-gauge/
Share on other sites

Yeah mine does similar - but only until about 50klms or so - after that it moves.

Skyline fuel gauges are notorious for being misleading....

for example, at the empty line once i pumped up to 45 ltrs indicating 20 ltrs left, then another time at the empty line i pumped up 55 ltrs indicating 10 ltrs left...go figure ;)

Edit - could explain why my friends r33 was full tank, then the next time he drove it - it was half tank....

Edited by emsta2003
Link to comment
https://www.sau.com.au/forums/topic/131466-fuel-gauge/#findComment-2432893
Share on other sites

Yep - I had the same sort of problem. Think I have solved part of it anyway. I picked up my mint S2 R33 25T 2 months ago and put in my first tank of fuel... Needle read full for about 120 kays then it jumped to empty. I shat myself cause I thought it had used a full tank in 120kays!! My mechanic replaced the sender unit in the fuel tank and this helped. The sender unit was half of the problem as it was stuffed. The guage still fluctuates a bit, so the next thing im looking at is the actual guage in the dash. I reckon it sticks. I have seen it jump from full to a quater in the space of seconds while I have been driving (with a new known good and tested sender unit in place)- SO... Out goes the instrument cluster ands in goes the 320kph nismo dash with much attention being paid to the fuel guage!! ;-)

Hope this helps u guys!

Cheers,

Chris.

Link to comment
https://www.sau.com.au/forums/topic/131466-fuel-gauge/#findComment-2432973
Share on other sites

the needle will move around a bit depending on the angle of the car. if you park sideways on a hill then it will change the reading. this is due to the position of the sensor. hold a glass of water at an angle. the water doesn't stay level with the cup, but level with the ground.

if you fill your tank right up you should drive about 30-50km before the needle moves. this is because you generally fill up well past what the sensor sees as full , so you use up fuel before the sensor reads any change.

Link to comment
https://www.sau.com.au/forums/topic/131466-fuel-gauge/#findComment-2434619
Share on other sites

yeah i mite have to replace the sender unit as i have already put in a different instrument cluster and it does the same thing does anyone know how much a new sender unit is? and will i have to get one through nissan? cheers for the help so far ;)

iLEC

Link to comment
https://www.sau.com.au/forums/topic/131466-fuel-gauge/#findComment-2439063
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...