Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Have it at south bank at the hotel that has those huge beer things I think its called wharf side or something. the marter hospital end of south bank right at the good will bridge.

Dam skyline owners you’re all like that Richard dude on the Pizza hut add. Tight Asses!!

If I had my licence and you'd ask I would :huh:

i vote for Nandos (again) purely because its on the same road... if you were prepared to drive to Harry's, then its only an extra minute to get to Nandos...

i have to be out of there by 8pm (start work at 8:30), so i can't go trapsing all over the southside :huh:

i'm heading to bed now, will be up again at 4:30... will see what you guys say between now and then... it might be that you guys decide to go somewhere completely different, without me... in which case, that's cool, and have a good dinner :P

Yeh executive decision made by the people important enough to post in this thread :)

NANDO's @ NEWMARKET @ 7PM... :rofl:

Good that I actually read the whole thread ...

Might want to change the first post next time so we know whats going on ... will come out to Nando's for some chicken then I guess

Good that I actually read the whole thread ...

Might want to change the first post next time so we know whats going on ... will come out to Nando's for some chicken then I guess

The first post would have normally be changed, but seeing as I didn't write it and I'm not a mod in this area I couldn't change it :D

Was great to meet you Frank and to catch up with those who came along :P

I'll be more organised next week guys :)

I went past there at about 8:30pm on my way home from the city (Nikon Training) and thought i wish tuesday night dinner was at nando's then i see this...

You would not have seen me as i was in a company car anyways... I could not stop either as i was not driving sorry and of course i didnt know you guys were there...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...