Jump to content
SAU Community

Recommended Posts

Hey guys im having some headaches with my R33 GTST. I put a sard fuel pressure reg on it on wednesday night n bumped the pressure up to 52psi at idle. 10psi more than stock reg showed, anyhow it ran fine for one day. Idled normal and ran beautifully on boost. Until the next day it developed a misfire.At cruise and idle would run on 5 cyls but on acceleration would clear itself up n run on 6.

basically i compression tested my engine all readings are the same so scratch that. i swapped coil packs around and number 2 was still the problem so scratch out coil packs. Had a look at all my plugs n they were all very black n number two was soaking wet.

Whacked 6 brand new plugs in there n started it up, after it cleared itself it ran on 6 cyls. had fuel pressure set at 36psi, as soon as i started to bump pressure above 42psi it started to run on 5 cyls again and number two n was still the cylinder misfiring.

Also another thing to note is my idle hunts sometimes when the misfire occurs, like its got a major air leak, 500rpm to 1500rpm n so forth until it stalls. but this isnt all the time. tried squirting water around the intake manifold on number twon injectors to see if it was sucking in air from the seal but no difference. Im stumped, anyone know the symptoms for a faulty injector??

Link to comment
https://www.sau.com.au/forums/topic/133666-how-to-diagnose-faulty-injector/
Share on other sites

why dont you swap injectors? Move no2 to say no3 and vice versa and see if the problem moves to cylinder 3...

Why are you bumping the fuel pressure up so high? You running an aftermarket turbo, trying to do a manual tune on it so you can run higher boost? Or is it knocking or something?

ok basically the reason i am trying to bump the pressure up is because i had it on the dyno n it made 346hp at the wheels but was running a tad lean top end so was trying to avoid buying injectors for now coz they are expensive, thought a fuel reg may work as a cheaper option coz i want to sell the car but now i have this issue, n the reason i dont change injectors around is coz its one hell of a mission to get the rail out to swap them over. cheers

ended up finding the problem wasnt injector, it was the new sard fuel pressure reg i'd put on, fuel was passing through the regulator into the vacuum line n being sucked into the front of the manifold n straight into number two pot hence the over fueling in that cylinder mainly but fouling plugs, and rough idle. Take vacuum line off top of reg and theres a constant stream of fuel coming out. took a day of driving to give way but yeah. shouldnt overlook new bits hey :s

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...